0
yes
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you apply a serpinetine belt on a 2000 impala with a 3.8 engine?
there is a diagram under the hood and in your owners manual of the belt routing, you have to release the tension on the belt tensioner and the belt will come right off and to put a new belt on just follow the routing chart and release tension on the tensioner to get belt back in place and when belt is back on all pulleys just let go of the tensioner and your done.
What happens when you put on to much belt dressing?
Clean all of the dressing back off and replace the belt.
How do you change a serpentine belt on a 1994 Chevy silverado?
take pressure off the belt by pulling back the spring tensioner. Remove old belt, put the new belt on all the pulleys but the idler pulley, pull the tensioner back slip belt on to idler, Look to make sure you have the belt on all pulleys good, your done.
Back Support Belt?
form_title= Back Support Belt form_header= Support your back while at work. What does your job entail?*- _ [50] Are you on your feet all day?*= () Yes () No What is your height and weight?*- _ [50]
How do you change alternator belt on Renault megane?
Depends what model Megane, Te 16v ones mostly had automaits adjusters that cannot be locked back and will probably require an extra set of handsd to line the belt up while the other person twists the belt tensioner to relase the pressure on the belt.Remember to have the belt fully lined up on all the right pulleys!
How do you put a serpentine belt backon after it sliped off?
If the belt slipped off, this is an indication that the belt is worn out or the tensioner needs replacing, or both. You put the belt back on by pulling the tensioner back, sliding the belt over all the pulleys in the correct manner, and releasing the tensioner to apply tension to the belt. There should be a diagram of the serpentine belt routing procedure under the hood of your vehicle.
How do you remove the AC belt so you can replace the alt belt?
There should be a belt tensioner pulley that is able to slide back and forth to tention the belt. Loosen that fully then take the belt off that will also be the same for the alternator if it is a V-belt Drive. if it is a serpentine belt the one belt will release the pressure from All the Pulley's.
Do you have to wear a seat belt in the back seat in Michigan?
I think it goes by age. If your 16 and older you don't have to, but all younger have to. Front seat driver and passengers all have to wear a seat belt
How do you remove alternator in a 1981 300D Mercedes?
The alternator is on the bottom-right of the engine. Jack up the right side of the car (chalk your wheels, ensure the transmission is in park, and the parking brake is set). Loosen the locknut on the alternator. Back off the tension on the belt with the tension bolt. Remove the belt and all wires attached to the unit. Remove the alternator bolt and unit.
How do you change the serpentine belt on a 1999 Volkswagen Beetle?
look at the top of where the serpentine belt is located. there is a pulley (called belt tensioner)with a square nipple sticking out the top of it. find a wrench the size of the nipple(via 3/4 or 7/8 etc..)and push towards the back of the car to loosen belt. now remove belt. now line up new belt following the belt route located under the hood. push the tensioner pulley back and pull belt on top pulley, making sure belt is still on all of the other pulleys hint: sometimes you have to take out the inner fender of the front right tire out and put a clamp on the belt and main pulley to hold it in place before you continue installing the rest of the belt.
How do you use all right in a sentence?
The back flip you just did was all right, but it wasn't perfect.
How do you change the timing belt on S500 Mercedes Benz?
The timing belt cover should be right behind the water pump .. So remove the water pump then remove the timing belt cover then remove the timing belt then do all them steps backwards
