You should not weld on concrete, as it can explode if heated
Yes, it should, I actually have a project that needs me to cut a cast iron pipe, and my soulution was to use a plasma cutter. The plasma cutter was develiped to cut both ferrous and non-ferrous materialls. Unlike a oxy-gas torch which is only good for steel which has a high Iron content, Plasma will cut steel, stainless steel (which has a much lower Iron content), Aluminum, and I am sure will cut other metals as well. The cutting action is based more on the extreme concentrated heat cutting the material more than a chemical reaction, or burning action of the material.
Two ways. Caulked joints and ty-seal joints. Cut the cast iron behind the hub and use a Clamp-all to join it to PVC pipe. If this sounds too difficult, CALL a Plumber.Why do you want to replace your cast iron? That would be alot of work, only replace what you need to. Unless it is your sewer line then i would replace it all to the main. I agree with answer # 1.IN ADDITION:Back in the day, cast iron joints were sealed together with hot lead. Depending on the position of the cast iron pipe and the size of it. Either one can cut the cast iron piping and clamp PVC to it or you can melt the old lead out of the cast iron joints and place PVC piping inside and then "recork" (reseal) it with prattley putty to prevent it from leaking.CORRECT1- Older CI roof drains were installed by Caulking using oakum and then pouring molten lead2- Some older CI drain drains used a Durham system meaning the Cast Iron drains were SCREWED the pipe galvanized in most cases and then the galvanized was caulked into a cast iron bell.It is unprofessional and highly unskilled to replace a cast iron leader line with plastic for several reasons.Seems the non skilled always try to use some type of epoxy..You may want to contact a licensed master plumber who has had the required 10,000 hr apprenticeship training
It is very easy to cut, however it would be difficult to cut into a desired shape. When you cut silicon you score it slightly then press it against an edge. However, it only breaks along the crystal lattice since silicon is usually available as a single crystal wafer. This means that you can only make clean breaks in the material. It does not "cut", you can only break it into pieces.
You remove the existing tub shoe and related fittings and install a new assembly. In some cases a reciprocating saw will be needed to cut the shoe flange located inside the tub
how do i cut cast iron
Balsa Wood
Very carefully drill a hole by each end of the split then gently grind a "V" shape in the split and then use a Cast Iron welding rod AFTER pre heating the base mental and allow to cool naturally as not to thermo-shock the metal
NO, it has to be cut with a cutting or grinding disc.
i think it is Easy to cut , since it is softwood. So relitivlly speaking , it should be. :/
Use a Barbie head. Sawzall with metal cutting blade to cut through pipe without damaging cast iron pipe.
I cut it with an abrasive fibre cutting disc on my angle grinder. I also cut all pipes this way, very fast and a clean cut.
Put a cutting blade on it and it shouldn't have water in it when you cut because of the possibility of shock.
In order to make iron, the following equipment must be used: shovels to unearth the iron ore, a crucible in which to heat the iron ore, a heat source in which to place the iron ore, a receptacle in which to pour the heated iron, a cooling area with liquid (often oil) to quench (or rapidly cool) the hot iron, a forge on which to shape the cooled iron and a forging tool (hammer or roller) with which to shape further shape and cut the iron to the desired specification.
PVC/Cast Iron/Steel/Plastic/ Depends on what type
You should not weld on concrete, as it can explode if heated
Igloos are built from large bricks cut from compacted snow, snow is easy to cut, and light-weight, it is easy to trim and form into the Igloo shape. Ice is very hard, very heavy and not easy to build with.