In Europe, low-voltage three-phase distribution is by means of a four-wire system (three line conductors and a neutral) supplied from a wye-connected transformer secondary. In North America, low-voltage is supplied from a delta-connected transformer secondary, one phase of which is centre-tapped and earthed (grounded). The single-phase supply to residences is then supplied by that particular phase, giving 240 V line-to-line and 120 V line-to-neutral. You can tell if you have a delta power when the phase voltage is equal to the line voltage and that you have a star power when the phase voltage =root 3(THE LINE VOLTAGE).
There is phase to phase voltage in 3 phase system.AnswerYou don't get voltage 'phase-to-phase'; it's 'line-to-line'!
My first thought is this is probably a corner grounded delta system, but I'm confused by your voltages. If this was a 460v (L-L voltage) ungrounded or corner grounded system, the phase to ground voltage is meaningless, but the phase to phas voltage will be 460v all around the delta. If you have a 460v system and you're only seeing 230v, there's something wrong.
The three phase voltage is 380 the hertz is 50
Currently, in popular usage, 3 phase systems are arranged in a "Y" or "star" configuration with the same voltage from each leg to ground. Primary sides of transformers are in a delta, "triangle", configuration but this is not the utilized side. In some old systems, the utilized system is delta with the mid point of one winding grounded. The phases at each end of this winding will measure half the volts to ground as from phase to phase. The phase farthest from the grounded winding measures a much higher voltage to ground than phase to phase since, in simple terms, it is measuring the voltage across 1 and 1/2 windings.
normally delta connection wired in 3 phase induction motor. during starting wiring is in Star and after running normal speed changeover to delta .beacause starting time its phase voltage equals less root3 times of line voltage ,line current and phase current equals. in Delta phase voltage and line voltage equals, and phase current equals root3 times line current
A: A DELTA transformer is a 1:1 voltage transfer delta to Y IS 1:2 voltage transfer. That is for 3 phase system, If the phases are not exactly matched or the voltage is not exactly right then on a Y setup there will be circulating current at the common node.
Star 220 v and delta 400 i star 58 percent only voltage applied delta 400v appliedAnswerThese figures do not represent three-phase, four-wire, system voltages, because if the line voltage were to be 440 V, then the phase voltage would be 254 V; or, if the phase voltage were to be 220 V, then the line voltage would be 381 V.
In Europe, low-voltage three-phase distribution is by means of a four-wire system (three line conductors and a neutral) supplied from a wye-connected transformer secondary. In North America, low-voltage is supplied from a delta-connected transformer secondary, one phase of which is centre-tapped and earthed (grounded). The single-phase supply to residences is then supplied by that particular phase, giving 240 V line-to-line and 120 V line-to-neutral. You can tell if you have a delta power when the phase voltage is equal to the line voltage and that you have a star power when the phase voltage =root 3(THE LINE VOLTAGE).
There is phase to phase voltage in 3 phase system.AnswerYou don't get voltage 'phase-to-phase'; it's 'line-to-line'!
VP = VL / √3 or VL = VP*√3. this will give you the values for a star connected system. If you using delta the VP = VL
My first thought is this is probably a corner grounded delta system, but I'm confused by your voltages. If this was a 460v (L-L voltage) ungrounded or corner grounded system, the phase to ground voltage is meaningless, but the phase to phas voltage will be 460v all around the delta. If you have a 460v system and you're only seeing 230v, there's something wrong.
voltage drop is be a problem.
Three-phase voltage in Germany is 400V, single-phase voltage is 230V.
6350.8 volts AC rms. The phase to earth voltage is ( square root(3) ) x lower than the phase-phase voltage on a 3 phase system.
The three phase voltage is 380 the hertz is 50
In a three phase three wire system, the phase voltage and line voltage are one in the same just different terminology. In a three phase four wire system, the line voltage is higher than the line to ground voltage. Line to ground is, line voltage divided by 1.73 (square root of three). For example 480volts /1.73 = 277 volts.AnswerIt depends upon the configuration of the three-phase system. For a delta (or mesh) connected 3-wire supply system, the line voltage is exactly the same as the phase voltage. For a wye (or star) connected 4-wire supply system, the line voltage is 1.732 (the square-root of 3) times the phase voltage.By way of explanation, for both wye and delta systems, phase voltages are measured across the windings of a three-phase transformer or across individual loads, whereas line voltages are measured between lines. For a wye-connected system, phase voltages can also be measured between any line and neutral.