0
Yes, Config t stands for configure terminal. This command is to switch into configuration mode .
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
What shortcut command can be used to enter the global configuration mode?
config t
How do you setup eigrp protocol?
router#config t router(config)#router eigrp 100 #net NETWORK ADDRESS
Which password allows the administrator to enter the privileged exec mode?
1) en2) config t
How do you set a default route on a Cisco IOS router?
ROUTER>enPassword:ROUTER#conf tROUTER(config)# ip route 0.0.0.0 0.0.0.0 insert gateway address hereROUTER(config)#endROUTER#exitSo to recap. type 'en', then your password, then 'conf t', then ip route 0.0.0.0 0.0.0.0 something, then end and exit to logout :P
What are the cisco IOS modes?
IOS has many different modes, the main ones being user exec and privileged mode. Both usually require authentication to enter. So when you initially telnet into your router you are in basic mode. This allows you to do very few commands, such as ping, telnet to another host, and get statistical information. Access to all configurations are off limits, even for viewing.User Exec ModeWhen you first log in, you are already at user exec mode. You can also tell because you are given the ">" prompt. Privileged Exec ModePrivileged Exec Mode is simply the administration mode for the router. This mode by itself allows you to view router settings that are considered private. To get into the privileged exec mode you must use the enable command. Clue: People with a clue would type 'en' to enter privileged exec mode.The Privileged exec mode is given the "#" prompt. A few of the common commands are listed below:show access-list - displays all access lists and the number of matches each line has received since the access list was applied.show interface - displayes the mani configurations of all interfaces.show interface summary - (IOS version 12.0 and newer) Displays a quick summary of all interfaces.Privileged mode has a a few sub modes as well such as global configuration mode, interface configuration mode, and routing configuration mode, which are described below. You can think of the different modes as a tree that give you more access and more specific configurations as you traverse down the branches.User Exec Mode | Privleged Mode (en) | Global Configuration (conf t) | | Interface (int ...) Routing (route..)
How do you recover the password for a Cisco 2600 router?
First, get yourself a serial cable and access to the console port. When you have that arranged, try to get (unprivileged will do) access to the router's prompt and run a show versioncommand. Record the value of the configuration register. If you can't login, you can assume it's 0x2102.Next, powercycle the router. Within 60 seconds of power on, send a BREAK key down the serial console to put the router into ROMMON mode, which stops it booting IOS.At the prompt rommon 1> type confreg 0x2142 to instruct the router to boot from flash, but not load the startup-config. Type reset next.After the router is restarted it'll ask to go into setup mode, don't do that.Type enable or en.Type copy start run.Type show run . You will see some passwords unencrypted, which you can simply write down. The enable secret, if used, will be encrypted and must be reset.Type conf t .Type enable secret to reset the enable secret to your new password.Issue a no shut for each interface you use.Type config-register 0x2102 (or the value you wrote down earlier)Type end .Type copy run start to save your changes.
How can you configure a router Cisco?
Well what sort of application is the 2600 router going to be used in? Here is a short thing about setting the clock http://www.learnios.com/viewtopic.php?f=4&t=36 Here a little more on setting up interfaces http://www.learnios.com/viewtopic.php?f=72&t=34 Here is password recovery steps http://www.learnios.com/viewtopic.php?f=4&t=28 Setting up cisco routers can be done many ways if you are looking for and more direct answer I suggest asking a more direct question like "how do I setup DCHP on my 2600" or how do I ip interfaces
Which cable is used t connect router to router?
If the router is not smart enough to tell the difference then you will need a crossover.
Does At and t U-verse offer a Wireless N-router?
Yes, in fact the router AT&T U-Verse sends you has built in WIFI. Unfortunately, they charge more than its worth for the router.
I have looked into t?
I have looked into this and your router does not support wireless. You will need a wireless router to connect your nook.
Is there a quiz about router bits?
Toolstoday Router Bit Profile Quiz Do you know your router bit profiles? Test your knowledge with the Toolstoday Router Bits Quiz. Name that router bit. http://www.toolstoday.com/t-router-bits-quiz.aspx
How do you assign IP to cisco switch?
You can't assign an ip to a switch but you can add one to the interfaces......... like: for the management vlan (or any other vlan) Switch(config)#int vlan 1 Switch(config-if)#ip address {your ip address} {mask} Switch(config-if)#no shutdown any other port Switch(config)#int <fa, G, S> <interface number i.e. 0/0> Switch(config-if)#ip address {your ip address} {mask} Switch(config-if)#no shutdown and for a default gateway Switch#conf t Switch(config)#ip default-gateway {ip address}
