0
Is defined as a small but allowable amount of variation from a specified resistance measurement?
Wiki User
∙ 10y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you determine the minimum allowable voltage between line and neutral?
The voltage between line and neutral is determined by the regulations in your country. This is specified as a nominal (named) voltage, together with its allowable variation expressed as a percentage of that nominal value. In the UK, for example, this is 230 V (+10%/-6%).
Compare method of undetermined coefficients method of variation of parameters?
this questions isn't specified enough to be answered
What is the relation between internal resistance and load resistance when current is constant in the circute?
The total resistance of a circuit is the sum of the supply's internal resistance and its load resistance, because they are in series with each other. This is true regardless of the magnitude of, or the variation in, the current.
What is percentage regulation in transfarmer?
percentage regulation is defined as [{v(no load)-v(full load)}/v(full load)]*100% it gives the variation of output dc voltage(voltage across load) with variation in load resistance
Which of the material is used for the swamping resistance that is connected in series with the working coil of a voltmeter?
A swamping resistor is usually manufactured from the metal alloy manganin (trade name), or other alloy with similar resistance/temperature characteristics -i.e. practically zero temperature coefficient of resistance. In other words, its resistance will remain more-or-less constant over a wide range of temperature variation.
How do you determine the minimum allowable voltage between line and neutral?
The voltage between line and neutral is determined by the regulations in your country. This is specified as a nominal (named) voltage, together with its allowable variation expressed as a percentage of that nominal value. In the UK, for example, this is 230 V (+10%/-6%).
What is considered to be the maximum allowable supply voltage variation?
+or- 5%
What is the meaning of measurement of variation?
Mean
Definition for tolerance value of a resistor?
An allowable amount of variation on either side of specified measure. If a resistor is labelled as 100 ohms, with 20% tolerance, it might be anywhere from 80 to 120 ohms. If a resistor is labelled as 100 ohms with 10% tolerance, it should range between 90 and 110 ohms. If a resistor is labelled 100 ohm with 5% tolerance, it could vary between 95 and 105 ohms. A tolerance is both ways, if a measure has 10% tolerance, then the total variation is 20%, plus 10 added to minus 10. If you are talking about variation to one side alone, the term is "deviation". If a resistor is supposed to be 100 ohms and actually tests at 105 ohms, it deviates by 5%, but is within allowable variation if it is specified to be within 5% tolerance.
What is the normal allowable source voltage deviation from the motors nameplate voltage rating?
It can be 10% min and 5% max.AnswerA nameplate voltage is a 'nominal voltage', and manufacturers normally design their products for the allowable variation in nominal voltage of the country in which they are to be marketed. So, for those products intended for, say, the British market, manufacturers would take into account the British allowable variation, which is 230 V (+10%/-6%). And, no doubt, most manufacturers would widen this variation to allow a 'factor of safety' for their products.
Which term is defined as part of a resistance training program that systematically alters exercise over time?
Variation is defined as part of a resistance training program that systematically alters exercises over time.
What is an anova test?
An ANOVA is an analysis of the variation present in an experiment. It is a test of the hypothesis that the variation in an experiment is no greater than that due to normal variation of individuals' characteristics and error in their measurement.
What is another word for aggredation?
Change, difference, level, variation, measurement or position
What is a statistical measurement that describes the variation of a data set called?
Standard Deviation
What is difference between variation and provisional sum?
Provisional sum is an amount quoted for an item in a tender document where all of the design information is not fully specified. The provisional sum should be as accurate as possible with the information to hand A variation is an item within a construction project that was not originally specified in the contract tender document and so is a 'variation to contract'.
What system of measurement?
The worldwide system of measurement is called SI (short for Système international d'unités). It is a variation of the metric system.
Compare method of undetermined coefficients method of variation of parameters?
this questions isn't specified enough to be answered
