0
Is it necessary to fill nozzle of burette in titration experiment?
Wiki User
∙ 13y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is a titration?
A titration is the use of carefully measured amounts of a known solution to determine the concentration of another. They often involve acid-base neutralisation or oxidation-reduction reactions (examples would be sodium hydroxide with hydrochloric acid, or permanganate with an iron solution). The main part of the system is the burette, a large graded tube with a controllable variable nozzle at its end. This nozzle is used to add different amounts with great precision to the solution being tested, so that an exact reading can be made - if done correctly, the titration's accuracy is limited only by the scale on the burette. A sample of the test solution (collected using a pipette with a known volume and high degree of accuracy; the sample is called an aliquot) is placed in a container, usually a conical flask, under the burette. The burette is filled with known solution, i.e. one where the concentration is know to another high degree of accuracy. The two are mixed slowly and allowed to react - for acid-base titrations an indicator will be added to the flask, for redox the solution which will change colour is put in the burette. This is continued slowly until the solution will barely react with that from the burette. At this point the amount of solution taken from the burette is recorded. Ideally, the next slightest drop of burette solution will cause a change in colour of the solution that does not change at all. If not, the new recording is made and the last step repeated. This amount is a titre. The whole experiment is repeated several times. The data is collected and averaged out. From this, an amount of known solution used, an amount of tested solutio used and eventually a concentration can be found.
What is the function of atomizing air in burner?
to sprate the oil same into tha nozzle.
Why is the nozzle hole made much smaller than air inlet?
The nozzle hole is much smaller than the air inlet for some good reasons. The main reason it is smaller is because it allows it more strength, and to increase output power.
Why should the matchstick be held in 1 cm below the nozzle when lighting the burner?
It doesn't need to be
What happens when the push button on an aerosol spray can is pressed?
the pressurized product is forced up thru the straw and hit the nozzle and expands
How do you clean pipette?
First remove all the solid particles from the burette using a scrubber. Then wash the burette with tap water followed by distilled water thoroughly (even the nozzle). Then wash the burette with the solution to be used in the burette.
What is a titration?
A titration is the use of carefully measured amounts of a known solution to determine the concentration of another. They often involve acid-base neutralisation or oxidation-reduction reactions (examples would be sodium hydroxide with hydrochloric acid, or permanganate with an iron solution). The main part of the system is the burette, a large graded tube with a controllable variable nozzle at its end. This nozzle is used to add different amounts with great precision to the solution being tested, so that an exact reading can be made - if done correctly, the titration's accuracy is limited only by the scale on the burette. A sample of the test solution (collected using a pipette with a known volume and high degree of accuracy; the sample is called an aliquot) is placed in a container, usually a conical flask, under the burette. The burette is filled with known solution, i.e. one where the concentration is know to another high degree of accuracy. The two are mixed slowly and allowed to react - for acid-base titrations an indicator will be added to the flask, for redox the solution which will change colour is put in the burette. This is continued slowly until the solution will barely react with that from the burette. At this point the amount of solution taken from the burette is recorded. Ideally, the next slightest drop of burette solution will cause a change in colour of the solution that does not change at all. If not, the new recording is made and the last step repeated. This amount is a titre. The whole experiment is repeated several times. The data is collected and averaged out. From this, an amount of known solution used, an amount of tested solutio used and eventually a concentration can be found.
WHAT IS SR Nozzle?
SR nozzle means "Self Reinforced Nozzle".
What is the nozzle coefficient of a bit nozzle?
0.42
What is convergent divergent nozzle?
Convergent nozzle indicates nozzles will converge with an end closing together at the end divergent nozzles increase size at the end. If air flows in this direction: ---> Convergent nozzle > Divergent nozzle <
How does a wedco model 40730 nozzle work?
The Wedco Nozzle is a CARB compliant spill-proof gas can nozzle. With the nozzle in place you can invert your gas can and it will not leak. Then simply push the nozzle lock and push the nozzle against the rim of the filling throat of the tank you're filling to start the flow of fuel. If you lift the nozzle away from the rim the flow stops.
Where is the rocket nozzle in super Mario sunshine?
You get the rocket nozzle after you open the rocket nozzle box in the level with the blooper boss.
What is the difference between a shell nozzle and a regular nozzle?
About 2 inches
How do you get the rocket nozzle in Super Mario Sunshine?
Jump on a red box with a weird symbol on on it and take nozzle that comes out. You have obtained the rocket nozzle.
How do you get in the building with nozzle boxes in super Mario sunshine?
Use the turbo nozzle.
How do you freeze water without cold?
Pressurize it through a small nozzle. It will freeze at the nozzle.
How do you use nozzle in a sentence?
My baby brothers baby bottle has a nozzle the size of an elephant!
