answersLogoWhite

0


Best Answer
Copy

Yes it can be. I think you need to replace the whole hub assembly

User Avatar

Wiki User

โˆ™ 2011-09-14 12:28:43
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: Is replacing the wheel bearing on a 2000 Chevy Blazer a do-it-yourself job?
Write your answer...
Submit

Related Questions

How much does it cost to replace the wheel bearings on a Chevy Blazer?

Replacing a wheel bearing in your Chevrolet blazer will cost approximately $175 per bearing. You can save $125 by doing the work yourself.


Can you replace a speed sensor on a 1998 Chevy Blazer without replacing the whole hub and bearing assembly?

yes you can but good luck finding one


Do you put grease on a wheel hub bearing on a 1998 Chevy blazer?

No. That is a factory sealed bearing.


What makes Chevy blazer air compressor squeal?

bad clutch bearing


What size is the front wheel bearing hub nut on a 2000 Chevy blazer?

35mm


Is wheel bearing on a 4 wheel drive Chevy blazer pressed in?

no the hub and bearing are 1 peice and pretty easy to changs


What size in the front wheel bearing hub nut on a 2001 Chevy blazer?

34 mm


What size is front wheel bearing hub nut on a 2000 Chevy Blazer?

36 mm


1987 Chevy blazer wont turn over after replacing starter?

did you check your battery and alternator?


Will the doors from a 98 Chevy blazer fit a 2001 Chevy blazer?

Yes, the doors from a 98 Chevy Blazer will fit a 2001 Chevy Blazer with a little moderation.


How to replace a wheel bearing assembly on 1999 Chevy blazer?

Check related answers. There are several responses and are quite accurate.


How do you repair OBDII code P0442 on a 2001 Chevy Blazer?

You have a small "EVAP" leak. Start with replacing the fuel cap.


What size is the front wheel bearing hub nut on a 1998 Chevy blazer s10 4x4?

36mm. You will also need an 18 mm box wrench to replace the bearing assembly.


Will 98 Chevy Blazer doors fit 97 Chevy Blazer?

Yes.


Will a transmission from a 85 Chevy K5 blazer 4x4 fit an 87 Chevy k5 blazer 4x4?

can I put a 99 Chevy 4l60e transmission in my 86 k5 chevy blazer


How can you repair a power seat in a 1996 Chevy Blazer that suddenly stopped working?

my Chevy blazer power seat on my 1996 Chevy blazer isn't working


1998 Chevy blazer roaring noise quits when you slightly turn steering wheel to right?

Worn right front wheel bearing.


Will a 95 Chevy Blazer grill and headlights fit on a 96 Chevy Blazer?

Fit 96 grill in 95 blazer


How do you get a pulley off a 1998 Chevy Blazer?

HOW TO GET A PULLEY OFF A 1998 CHEVY BLAZER


Will a 2003 s10 Chevy Blazer transmission fit a 2002 Chevy Blazer?

Yes


Where is the horn located on a 1991 Chevy Blazer?

Where is the horn located on a 1993 chevy blazer


Will an alternator from a 2000 Chevy blazer fit a 2002 s10 blazer?

An alternator from a 2000 Chevy blazer will fit a 2002 S10 blazer with a little fabrication.


Where can you find a step by step diagram for replacing a 4.3L motor in a 96 Chevy blazer?

Purchase a shop manual for that vehicle. Try Helm.com


1993 Chevy blazer 4x4 serviceble wheel bearings or hub bearings?

It has 1 big hub bearing per side and you can not service them. It has factory sealed bearings. If there bad then you must replace the bearing.


What caused your 1998 Chevy Tahoe to loose oil pressure after replacing rod and main bearings?

Perhaps excess bearing clearance?