0
What else can I help you with?
How do you tighten struts on Chrysler 1999 Sebring?
Struts are not adjustable, and must be replaced if faulty,
Why is the lights flashing when turned off and a clicking noise on my 1996 Chrysler sebring Theft system?
Could be a faulty relay!
You got a 96 Chrysler sebring convertible and the battery is keep on going bad any ideas This will be third one replaced?
I have a 1996 Chrysler sebring convertible and I have had a new battery go bad three times in two years. Chrysler dealers across America could not solve the problem. I wound up stranded in a little town called Olds, Alberta, about 60 miles north of Calgary, Alberta, on a weekend in a hail storm and my car would not start. The nearest Chrysler Dealer in town fixed the problem in a couple hours. The problem was a faulty fuel-pump sending unit which caused a slow electrical power leak from the battery.
What causes cylinder 2 to misfire in a 3.0 2001 Chrysler sebring?
The causes for cylinder 2 to misfire in a 2001 Chrysler Sebring with a 3.0 engine is a faulty spark plug or a damaged spark plug wire. In-depth troubleshooting can be completed by a local mechanic or dealership.
I have a 2007 chrysler sebring 2.7l that will not start without spraying starter fluid in the air filter Does anyone know what the problem is?
If the 2007 Chrysler Sebring 2.71 is not starting without stater fluid in the air filter is could indicate a faulty starter or the air filer may need replacing.
98 Chrysler sebring conv what could cause loss of power?
Loss of power in a 1998 Chrysler Sebring convertible could be caused by several factors, including a failing fuel pump, clogged fuel filter, or issues with the ignition system such as worn spark plugs or faulty ignition coils. Additionally, problems with the air intake system, such as a dirty air filter or malfunctioning mass airflow sensor, can also lead to reduced engine performance. It's advisable to perform a diagnostic check to pinpoint the exact issue.
2000 Chrysler Sebring convertible fan only works on high I replaced the resistor it still only works on high if the switch is faulty would this be the cause of the problem or something else Thanks?
I had the same problem with the same year car. I've replaced the resistor several times. It works for months & then it stops working again. I think this is the 4th time I replaced the resistor, it is working okay now. I think it is a defect in with this cars fan system. I had a similar problem with my 2001 Sebring Convertible. I had the blower motor replaced, and now the fan works perfectly.
How can I fix 2000 Chrysler Sebring JX instrument cluster voltage problem?
Using a multimeter and spark tester will help find the source of a voltage problem on a 2000 Chrysler Sebring. Having a repair manual on hand will troubleshoot the system, but many electrical problems require tedious sifting through wiring to find the faulty short or ground which is causing an issue.
What would make your 1996 chrysler sebring shut off when im driving. i changed the alternator and starter and the transmission is rebuilt. and its making a ticking noise when i try to start it back up?
Faulty fuel pump
What is code p0118 in a 2003 Chrysler Sebring?
Code P0118 in a 2003 Chrysler Sebring indicates a problem with the engine coolant temperature (ECT) sensor. This code is triggered when the engine control module (ECM) detects a voltage reading from the ECT sensor that is higher than the expected range, suggesting a potential short circuit or a faulty sensor. It can lead to issues such as poor engine performance or increased emissions. To resolve this, it is recommended to inspect the sensor and its wiring for damage or corrosion.
How to repair the tach and odometer on a 1997 Chrysler Sebring?
To repair the tachometer and odometer on a 1997 Chrysler Sebring, first check the vehicle's fuses and wiring for any damage or disconnections. If these are intact, you may need to remove the instrument cluster by unscrewing it and carefully disconnecting the wiring harness. Inspect the circuit board for any faulty solder joints or components, and replace or resolder them as necessary. If the issue persists, consider replacing the entire instrument cluster or consulting a professional for further diagnosis.
Why would a 1997 chrysler lhs temperature gauge read hot?
Engine is overheating, faulty gauge, faulty temp sensor......
