0
Metal spike with a hole at the end througe which you pass a rope are called?
Wiki User
∙ 15y ago
a needle
Wiki User
∙ 15y ago
Anonymous
Add your answer:
Earn +20 pts
What is the Diameter of CD center hole?
15 mm
What is hobble used for in drilling?
Hold up the elevators to trip in the hole.
What does AOH stands for in oilfield tubulars?
AOH is a type of connection used in the Oil and Gas industry it stands for American Open Hole
How do you make a simple machine windmill?
1.1Take the propeller off the flower. The flower's propeller will be used to spin the axle. A propeller from a larger pinwheel flower is best.2Place the spools between the plastic sheets and glue them on. These small spools should go at the corner of the plastic. Use super glue to attach the spools, and let it dry. This will serve as the casing for the windmill generator.3Measure the metal rod and drill holes in the plastic. The metal rod will go through the hole. Make sure the holes are perfectly aligned on both sides. Place the rod through the holes in the plastic.4Place the magnets in the casing. They should have enough space to rotate freely around the axle that will spin the magnets. Attach the magnets together using spacers. If there is not enough space between the spacers to insert the axle, the magnets are useless to generate electric current.5Put the rod in the hole. Wrap the wire around the generator. Wrap the wire around the casing 225 to 300 times.6Attach the propeller to the axle. The propeller from the wind decoration should be large enough to catch the wind. Place the propeller on a metal rod, and apply superglue.7Remove insulation from the wires. Attach the leads to the end of the low voltage and amperage light bulb.8Place the generator in a breeze. See if the wind can provide enough power to light the bulb. (If there is not enough wind, electrical current can be generated by manually spinning the axle rapidly.Tips & WarningsBecause the wind is not always available, the propeller may not rotate the magnet quickly enough to light even a small electrical light bulb.
What simple machines are found in a Ferrari?
wheels- wheel axle gear shift- lever pedal- inclined plane, lever seat belt- pulley mirrors- inclined plane Shocks and brakes have wedges, and also screws hold the car together.
What is the metal container in a golf hole called?
It is usually called the cup, and it is not always metal.
What is the Flat piece of metal framing a key hole called?
Escutcheon
How do you change storm aquario modes?
To change aquario from spike mode to its hole form you have to pull it down to change it to hole mode and push it upward for spike mode
What does to spike a cannon mean?
The phrase 'to spike a cannon' meant to disable it by driving a tapered wrought iron plug, or spike, down the touch hole with a hammer until it was level and firmly embedded.
What is the difference between blanking and punching?
Blanking and punching are both shearing operation. The difference is only in the scrap. In blanking what you cut out is of interest.In punching what you cut from is of interest.For example: You cut a hole in a sheet metal. If you are interested in the disc that is cut out, then the process is called blanking. The sheet metal with a hole through it is the scrap. If you are interested in the sheet metal that now has a hole through it, then the process is called punching. The disc is the scrap.
What happens when metal plate with circular hole is heated?
The hole decreases due to metal expansion.
What are metal hole saws used for?
Metal hole saws are used to drill circular holes in wood and metal. They are typically used in construction and woodworking to create openings in materials.
Where can one purchase a metal hole punch?
There are many office supply stores that sell metal hole punches. Some of the best include Office Max, Staples and Office Depot. You can also find a metal hole punch on Amazon.
If you heat a piece of metal with a hole in the center how will the size of the hole change?
It would get larger due to the expansion of the metal (see the related links)
What is the best way to spike a watermelon?
cut a small hole or a plug in the top of the melon, than slowly pour your alcohol of choice into the hole seal it with the saved plug!
Wjich of the following tools is used to mark the spot where a hole is to be drilled in piece of metal?
the small spaceabove the piston in which fuel burned is called the
What you called the hole in your stomach?
a hole in your stomach is called an ulcer
