0
Steam turbine nozzle clearance is the total energy content available in steam. This is through a valve.
Wiki User
∙ 9y ago
Wiki User
∙ 9y agoNozzle clearance to steam turbine is the total energy content available in steam. This is through a valve.
Add your answer:
Earn +20 pts
what is purpose of nozzle in steam turbine?
It sends hot gases from the combustion chamber to the 1st stage turbine blades at the correct angle and speed
What is the working principle of steam turbine?
The Steam Turbine is the one which steam worked pressured Hot and exited then the shaft of the turbine starts to and fro motion due which energy is injected through nozzle in the receiver.
Why is convergent-divergent nozzle generally used in steam turbines?
A convergent-divergent nozzle is generally used in steam turbines. This is because it drives generators in producing electricity with the use of turbine rotors with curved axes.
Why is nozzle control governing not employed a reaction turbine?
in reaction turbine pressure compounding is employed as every stage has a set of nozzle ring nozzle control is not feasible.
What is different betweeb single stage and multi stage steam turbine?
In a single stage steam turbine the steam is run through a nozzle to give it maximum velocity, thus the blades move at very high speeds, impractical for some applications, and only some of the energy is used, about 85-90%. In multi-stage or compound turbines the steam goes through a nozzle to increase its velocity, then after going through a set of blades, it is run through another nozzle to bring the steam back up to the correct velocity. After multiple stages there is no longer enough pressure left to up the velocity of the steam. This method increases the efficiency of the turbine and also decreases wear on the components caused by the high speed of a single stage.
what is purpose of nozzle in steam turbine?
It sends hot gases from the combustion chamber to the 1st stage turbine blades at the correct angle and speed
What is the working principle of steam turbine?
The Steam Turbine is the one which steam worked pressured Hot and exited then the shaft of the turbine starts to and fro motion due which energy is injected through nozzle in the receiver.
What is the clearance gap setting of a steam turbine thrust pad?
0.2 to 0.25 mm
Why is convergent-divergent nozzle generally used in steam turbines?
A convergent-divergent nozzle is generally used in steam turbines. This is because it drives generators in producing electricity with the use of turbine rotors with curved axes.
Why is nozzle control governing not employed a reaction turbine?
in reaction turbine pressure compounding is employed as every stage has a set of nozzle ring nozzle control is not feasible.
What is different betweeb single stage and multi stage steam turbine?
In a single stage steam turbine the steam is run through a nozzle to give it maximum velocity, thus the blades move at very high speeds, impractical for some applications, and only some of the energy is used, about 85-90%. In multi-stage or compound turbines the steam goes through a nozzle to increase its velocity, then after going through a set of blades, it is run through another nozzle to bring the steam back up to the correct velocity. After multiple stages there is no longer enough pressure left to up the velocity of the steam. This method increases the efficiency of the turbine and also decreases wear on the components caused by the high speed of a single stage.
What does steam do to a turbine?
Steam (under pressure) comes into contact with the blades of the turbine through which it is flowing and, by the direct application of force, causes the blades to move, turning the turbine shaft. The turbine coverts the thermal energy of the steam into (rotating) mechanical energy. Surf on over to our friends at Wikipedia using the provided link and get more info. Oh, and check out the pics! Answer it depends what type of turbine one is using types of steam turbine 1 impulse turbine 2 reaction turbine in 1 st one steam is completely expanded inside nozzle and all pressure energy get converted in to kinetic energy using this impulse force turbine runs. in 2nd steam is multiple stage blades are used where high pressure superheated steam gets expanded inside the turbine in each stage and after each stage velocity of steam increases. very high temperature superheated steam is reaquired because it has very high specific volume which helps in reducing mass flow rate of steam.
How does a terry turbine work?
Terry was the name of a steam turbine manufacturer. The company was bought by Dresser-Rand some years ago. I don't think they sell this model now, only spare parts. The basic design is that of an impulse turbine (as opposed to a reaction turbine). The unique feature with Terry is the nozzles feed steam radially inward to a single rotating wheel with blading on the circumference. The blades are semi-circular so the flow path is spiral between the blades and the stationary nozzles. They are arranged in sets of an inlet nozzle with 4 or 5 reversing nozzles before the spent steam is exhausted. The number of nozzle sets depends on the steam rate.
Why extraction taken from steam turbine?
Why extractions are taken out from steam turbine.
Why would you not heat the steam coming out of turbine and feedback to turbine?
becouse this steam is use repetdly for the turbine
What are the preventive maintenance of steam turbine?
The preventive maintenance of steam turbine mainly entails frequent servicing of the parts. This will ensure a smooth performance of the steam turbine.
What type of cycle used in steam turbine?
Rankine cycle is used in steam turbine
