answersLogoWhite

0

It is mounted on the side of the washer reservoir inside the

passenger fender. If rear washer isn't working, check for a crimped line to it first.

Also, wax may have plugged the jet. Take a small wire (guitar strings work) to unclog the jet.

Failing all, check the connector to the pump and the switch itself.

Good Luck!

auntetr

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How do you replace the windshield washer motorpump on a 1993 mercury villager gs?

Remove the wiring harness from the back of your 1993 Mercury Villager windshield washer motor pump. Remove the windshield washer pump hoses. Remove the windshield washer pump retaining bolts. Reverse the process to install your new windshield washer motor pump.


Where is the windshield washer motor located on a 1993 Saturn sc2?

It is connected to the washer tank.


Winsheild washer pump does work 1993 Toyota Celica?

Windshield washer pump does not work? Check hoses to hood. If disconnected from nozzles, it will just spray the engine. also check to see if hoses are caught between something (crimped). If not, remove fender on pump reservoir side of vehicle, remove pump from side of reservoir and replace with a new one.


If your 1993 Buick Lesabre windshield washer will not work and you have replaced the pump on the windshield washer storage tank and put a new windshield wiper motor on it what should you do next?

you should check your electrical connection at the "pump" terminal if there's no power then trace that wire back and see where the problem is.


Where is the battery in a 1993 Chevy Lumina?

If you look on the right side of your car, you'll see the windshield washer fluid, under a black metal bar. You have to take the black metal bar off, then you have to take the windshield washer fluid tub out.


Where is the computer located on a 1993 Jeep Grand Cherokee?

It is on right side firewall under the hood behind the windshield washer bottle


How do you replace a starter on a 1993 Toyota Celica?

bolt pattern for 1993 toyota celica starter


Where is the rear window reservoir on a 1993 Plymouth Grand Voyager?

First check under the hood, there might be a separate reservoir for it right by the windshield washer reservoir. It might also be at the back, lift the tailgate and there might be a little cap with a windshield wiper logo. Or the rear window washer might work off the front windshield reservoir. If it's shared at the front, then you'll have to keep the windshield washer fluid above the middle line on the windshield washer reservoir tank at least. Open the rear hatch. On the driver's side, there'll be a filler cap which is used to fill the rear window washer reservoir.


How do you disable 1993 Mitsubishi 300GT low windshield washer fluid dash indicator light?

To disable the low windshield washer fluid indicator light on a 1993 Mitsubishi 3000GT, you can locate the washer fluid level sensor, typically found in the washer fluid reservoir. Disconnect the sensor's electrical connector or remove the sensor entirely; however, this may lead to the light staying on regardless of fluid level. Keep in mind that disabling the indicator is not recommended, as it can prevent you from knowing when to refill the washer fluid.


Will a 1991 Toyota Celica hood fit a 1993 celica?

yes it will.


Where is the windshield washer fluid reservoir in a 1993 Maxima?

on my 1993 GXE the winsheild washer fluid reservoir is under the hood near the front of engine by antfreeze reservoir the fill tube is on the passenger side near the coolant reservoir. access to the "tub" itself and the washer motor/pump is from the passenger side front wheel well.


How do you replace a windshield washer pump on a 1993 Mazda 626 DX?

To replace the windshield washer pump on a 1993 Mazda 626 DX, first, disconnect the negative battery terminal to ensure safety. Then, remove the washer reservoir by unscrewing any fasteners and disconnecting the hoses. Take out the old pump from the reservoir, install the new pump, and reconnect the hoses and electrical connector. Finally, reassemble the reservoir and test the pump to ensure it’s functioning properly.