0
check power coming into the breaker if both leads are hot it's a bad breaker
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you replace a 15 amp breaker in the circuit box?
The breaker will have a black wire connected to it. Turn off the main breaker and then disconnect that black wire from the breaker. The breaker will snap into the main bar. Remove the breaker and install the new one. Reconnect the black wire to the breaker and then install the cover and turn the main breaker back on.
Why is the power off on on breaker when it is not flipped off?
Turning the breaker on allows the power to flow through to the outlets, lights, and appliances on that circuit, so yes power goes to and through a turned on breaker. If the breaker is off, but the main power is on, power still get to the breaker, usually from the bus bar that runs down the middle of the back of the breaker box.
What is the smallest size circuit breaker found in the normal home?
The biggest circuit breaker in any home is the main breaker located in your main breaker panel that is installed where your electrical service cable comes into your home.
Can you install a 2 20 breaker into a breaker box that has space but all other breakers add up to more amps than the 200 amp main breaker?
Yes. You'll seldom run every circuit to full capacity. The main breaker will trip if all the individual circuits exceed the 200 amp rating of the main breaker.
How do you find out how big your main breaker box is?
Simple. Your main electrical panel will have a "main breaker". This will be a two pole breaker, usually at the top of the panel. It will have a number on the breaker "handle" such as 150 or 200. This is the maximum number of amps your panel can supply. Most newer homes, 1975 and newer have a 200 amp service.
Will turning off the main breaker turn off all the power to the circuit breaker box?
No. Power to all the circuit breakers will be cut off except for the Main power breaker. The Main power breaker (which supplies power to all other breakers and will say 100, or whatever your max breaker box power is, on it )will have power going to it all the time, unless power is turned off outside the house.
Is there a circuit breaker that is operated by a signal sent down the same cable that's supplying power to it?
yes it is the main breaker
What are precautions to be taken at the time of back charging of generator transformer?
Nothing. If your system can run your house while the main breaker to the power grid is off, then back charging will occur as a byproduct while the main breaker to the power grid is on and you are using less power than you are generating. During times of a power outage, you'll want to cut the main breaker to the power grid, so that your system doesn't try to power the entire neighbor hood.
What is the rating of the main circuit breaker of the 60kw power distribution panel?
200 amps
Why would power be received before breaker but with breaker on no power is in any recepticles?
The voltage before the breaker is from the distribution panel's buss bars. This voltage is controlled by the panel's main breaker. To have no voltage on the terminal of the breaker means that either the breaker is shut off or it has gone into a trip position. If it has tripped push the handle of the breaker to the off position and then to the on position. This should reset the breaker. If the voltage is not present at the output terminal of the breaker after resetting it, then replace the breaker as it has a fault in it.
Does a residential condo require a main breaker in each unit?
No, a residential condo does not require a main breaker in each unit. Typically, the main breaker is located in the electrical room or utility room of the building, and it controls the power supply to all the units. Each unit may have individual circuit breakers, but a main breaker is not required in each unit.
How do you replace a 15 amp breaker in the circuit box?
The breaker will have a black wire connected to it. Turn off the main breaker and then disconnect that black wire from the breaker. The breaker will snap into the main bar. Remove the breaker and install the new one. Reconnect the black wire to the breaker and then install the cover and turn the main breaker back on.
Why is the power off on on breaker when it is not flipped off?
Turning the breaker on allows the power to flow through to the outlets, lights, and appliances on that circuit, so yes power goes to and through a turned on breaker. If the breaker is off, but the main power is on, power still get to the breaker, usually from the bus bar that runs down the middle of the back of the breaker box.
Why is it that you get a reading of 120 volts from the main breaker but it wont power a lightbulb?
This is the type of reading that you would get with an open neutral.
You lost a voltage leg by connecting the ground wire to the circuit breaker but com ed wires are still energized?
Yes this could be true. The breaker to the load will have tripped. The main breaker should still be allowing voltage to the distribution panel because it did not trip. If the main breaker tripped then the distribution panel must have been close to maximum amperage and the shorting of the branch circuit was enough to trip the mains.
When a voltage leg is lost by connecting the ground wire to the circuit breaker are com ed wires still energized?
Yes this could be true. The breaker to the load will have tripped. The main breaker should still be allowing voltage to the distribution panel because it did not trip. If the main breaker tripped then the distribution panel must have been close to maximum amperage and the shorting of the branch circuit was enough to trip the mains.
What cause the Main Breaker trips when I start a 30KW 3-phase Motor(Star Delt Starter)?
The wiring is like this:[[30KW Motor ---- Star Delt Starter(100A Breaker inside) ----- 200A Breaker------50A Breaker(Inside the breaker box which located inside the factory) -----100A Main Breaker]]Once I try to start the Motor, the Main Breaker trips immediately.
