0
You can try to calculate the resistivity of nichrome? I mean the question is the resistivity of the material.
Faughn, Jerry S., Raymond A. Serway. College Physics. Pacific Grove, CA: Thomson Learning Inc, 2003: 538.
Resistivity: Constantan resistivity and temperature. Schlumberger Limited, 2007.
The State Education Department. 2006 Edition Reference Table for Physical Science Setting/Physics. Albany, New York: DOE. 2006-2007.
What else can I help you with?
How do you know that the sensor is bad?
Find out the ohms range it must be within and do an ohms test.
What is The ohm meter reads 40 ohms on the resistsnce x 10 range how much is resistance?
If the ohm meter reads 40 ohms on the resistance x 10 range, the actual resistance value is 40 ohms multiplied by 10. Therefore, the resistance is 400 ohms.
What is the resistance range for a fuel sending unit for a 1967 camaro?
0 Ohms empty, 90 Ohms full.
What is the ohms range for the fuel level gauge for an 94 yj wrangler?
Sender Ohm Range
What is the resistance range of a 100 ohm potentiometer?
Zero to 100 ohms.
What is the ohm range for the fuel sending unit for a jaguar XJS 1986?
2o ohms to 200 ohms is what i'm getting on my 87 model
Whet does 4-8 ohms mean?
this is range of 4 ohms resistance in an electrical device. Ohms is a measure of resistance in electrical qualities. Circuits and devices are rated , or measured for there resistance in ohms to meet a designed electrical need. Is this related to a speaker?
Megger value for single conductor?
It depends on the value of voltage being applied to the wire in normal use. Voltages up to 750 volts can be used on wires reading as low as .5 meg ohms. Engineers like to see 5 meg ohms on conductor readings.
What is the range of resistance of the fuel level sending unit on a 90-93 Ford Festiva?
Full position (up) - 7 ohms Half tank (middle) - 33 ohms Empty position (down) - 95 ohms
What is the soul purpose of a Fluke T5?
The Fluke T5 is voltage continuity and current tester, meaning that its purpose is to test the voltages, ohms and amps of electrical devices used primarily by electricians.
What ohm range fuel sending unit does a 1997 grand cherokee use?
In the up position, it should be 20 ohms. In the down position, resistance should be 220 ohms.
How Countiniuty check by ohmeter?
Continuity means a direct connection or low Ohms or zero Ohms. A wire and switch will read from 0 to 0.1 Ohms on a perfect meter. A light bulb might read 1 to 10 Ohms, as example. First, to see if the meter is working properly: To check how the meter reads continuity and see how to interpret, touch the probes together and note the reading. This is the reading you should see when testing the circuit if you have good continuity. Safety!: Never test continuity or ohms on a circut that has power energized. The meter can be destroyed internally, or even explode if Ohms function is used on high voltages. Now, a couple ways to check: 1.) DIGITAL METER: Put the ohm meter on the lowest Ohms scale, usually will be "200". If the meter does not have several separate Ohms switch positions, it might be an "auto-range" kind. In that case, just set it to Ohms. 2.) ANALOG METER: Put the ohm meter on the lowest Ohms scale, usually will be "RX1". Some inexpensive analog meters have only one range, so just select the Ohms function, or plug the probe into the Ohms jack. Put the probes to what you want to measure. the reading should be zero if measuring continuity. In some cases, the digital meter may indicate between 00.0 and 00.6 Ohms, this is normal because even the wires and probes have some resistance. The lower, the better. Note that very inexpensive analog meters cannot read Ohms this low accurately, but you can tell if the continuity is good or not, because it will read "0" or very close to that.
