0
Across a 480 volt three phase system, 480 volts should appear across L1 and L2, L2 and L3 and L3 and L1.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How does a 3-phase 115 volt power supply measure 200 volts in-between each phase?
You should have about 230 volts between any pair of 3-phase service legs: L1-L2, L2-L3, L3-L1. If the voltage measured between any one pair results in low or no voltage, then you have a fuse or circuit problem.
Can you single phase 220VAC in place of three phase 220VAC?
Yes, just use L1 and L2 ( just 2 of the 3 legs), or one of the legs to a neutral wire if equipped. Just make sure the voltage is the same as the 220 volts you wish to have with single phase service.
How does 120Volts single phase convert to 220Volts 3 phase when the 3 phase voltage should be 208Volts ie 120V x sq route of 3 equals 208V?
If you get 220 volts instead of 208 volts it means that the transformer supplying the circuit is wired in Delta with one of the legs center-tapped to ground.
What is the result when a 400v device's load is connected between the two phase legs of a 3 phase distribution?
It works normally. Well actually there are 380 volts across two lines of a 3 phase AC source, so it should work normally.
How do you convert 3 phase star configuration 380 volts supply into 220 volts supply?
The process of obtaining 220 volts from 380 volts is quite simple. 380 volts is a three phase four wire system voltage. The 220 volts is obtained by taking the sq. root of 3 which equals 1.73 and dividing it into the phase voltage. 380/1.73 = 220 volts. This holds true with any three phase four wire voltage system. 208/1.73 = 120 volts, 415/1.73 = 230 volts, 480/1.73 = 277 volts and 600/1.73 = 347 volts. This lower voltage is present on any of the three phase legs of the three phase system to the neutral which is grounded on a wye connection.
Why 380 volts line to line if connect line to neutral is 220 volts?
A voltage of 380 volts is a three phase voltage. On a three phase four wire system, each phase leg to neutral (grounded) will give you 220 volts. This voltage is obtained by dividing the phase voltage by 1.73, as the phase legs are generated 120 degrees from each other. Square root of three is 1.73 divided into 380 equals 220 volts.
How does a 3-phase 115 volt power supply measure 200 volts in-between each phase?
You should have about 230 volts between any pair of 3-phase service legs: L1-L2, L2-L3, L3-L1. If the voltage measured between any one pair results in low or no voltage, then you have a fuse or circuit problem.
How does 120 volts come from 208 volts?
208 is a three phase wye connection voltage. To obtain the each individual coil voltage the 208 is divided by 1.73 which equals to 120 volts. Hence you have 3 phase 208 voltage on the phase legs and 120 volts to the wye point which is grounded. This same formula is used on any 3 phase system. 600/347, 480/277, 208/120.
Can you single phase 220VAC in place of three phase 220VAC?
Yes, just use L1 and L2 ( just 2 of the 3 legs), or one of the legs to a neutral wire if equipped. Just make sure the voltage is the same as the 220 volts you wish to have with single phase service.
Can you get 120 volts from a 480 volts 3 phase Y generator?
NO, the 480 Volts Y -- is 4 wire system, with three wires which are hot legs @ 480 volts between each three hot legs. A mid tap is a neutral leg (ground) the white wire. Which gives 277 volts between it and any of the three hot legs. so a 4wire 480 volt Y system. Gives 480 /277 volts.
How do you convert 230v to 208 volts single phase?
A source of 208 volts can be obtained from any two legs of a three phase four wire 208 volt system. The two legs are classed as single phase 208 volts. The lead tags can be L1-L2, L2-L3, or L3-L1 all of which will give you 208 volts. Any of these lead tags to the grounded star point (wye) will give you 120 volts.
How does 120Volts single phase convert to 220Volts 3 phase when the 3 phase voltage should be 208Volts ie 120V x sq route of 3 equals 208V?
If you get 220 volts instead of 208 volts it means that the transformer supplying the circuit is wired in Delta with one of the legs center-tapped to ground.
What is the result when a 400v device's load is connected between the two phase legs of a 3 phase distribution?
It works normally. Well actually there are 380 volts across two lines of a 3 phase AC source, so it should work normally.
How do you convert 3 phase star configuration 380 volts supply into 220 volts supply?
The process of obtaining 220 volts from 380 volts is quite simple. 380 volts is a three phase four wire system voltage. The 220 volts is obtained by taking the sq. root of 3 which equals 1.73 and dividing it into the phase voltage. 380/1.73 = 220 volts. This holds true with any three phase four wire voltage system. 208/1.73 = 120 volts, 415/1.73 = 230 volts, 480/1.73 = 277 volts and 600/1.73 = 347 volts. This lower voltage is present on any of the three phase legs of the three phase system to the neutral which is grounded on a wye connection.
What happens if the source of 220 Volts originates from two legs of a 3-phase circuit?
Nothing happens. This is a normal way to obtain a single phase system from a three phase system.
Why does 277 volts leg to legs waves do not read 554 volts?
The reason 277v leg to leg does not measure 554 volts is each phase of the system is 120 degrees out of phase with each other and there fore will not read 554v leg to leg but 480v lag to leg. If you take 277 times the square root of 3 it will equal 480. The meters measure Root Mean Square or rms voltages and are designed to take this into their readings.
What is the difference between 277 volts and 240 volts?
These voltages are both wye connection three phase voltages. The voltage difference comes from the primary three phase voltage supplies. 277 volts is obtained from 277 x 1.73 = 480 and 240 volts is obtained from 240 x 1.73 = 415. 480/277 volts is a common three phase American voltage. 415/240 volts is a European voltage. In Canada a common three phase voltage is 347/600. The 240 volts could also be a single phase voltage in North America derived from a split phase secondary on a distribution transformer that supplies 120/240 volts to homes.
