If the GFI outlet is tripped (the outlet, not the breaker) then it is telling you there is a ground fault which must be fixed. If the GFI outlet is not tripped, and the breaker is not tripped, but it is still not providing power, then you have a loose connection or a wiring error.
Anything can go bad. A breaker is a mechanical device and can fail for many different reasons.
you have a magic power-generating CB find out how it works and you should make a fortune.
If the circuit breaker to a dryer, or to any load, keeps getting hot and trips the breaker, then either the load is pulling too much current or there is a loose connection in the breaker or breaker panel. Either condition must be fixed to reduce the risk of fire.
If the breaker trips when nothing is turned on it could be a mouse problem. If it only trips when certain lights or appliances are turned on one of them is probably the reason.If it trips when nothing is being turned on or off something is getting hot. You should then have qualified electrician look at it. Hope this is usefull.
For the entire circuit to go out, the breaker has to trip. The breaker tripping is what causes the loss of power to everything pulling power from that circut. Any single power surge at any point along the circut can cause it. If you have experienced what you are questioning, I suggest you have an electrician take a look at your wiring. You may have serious issues. Breakers a designed to protect the wiring from getting too hot. It's a safety feature for your appliances, your home and those who live in it.
A circuit breaker/fuse is designed to protect the wiring from getting overloaded.
Anything can go bad. A breaker is a mechanical device and can fail for many different reasons.
you have a magic power-generating CB find out how it works and you should make a fortune.
If the circuit breaker to a dryer, or to any load, keeps getting hot and trips the breaker, then either the load is pulling too much current or there is a loose connection in the breaker or breaker panel. Either condition must be fixed to reduce the risk of fire.
Bad ground? How do i check this? See if you are getting power to motor? How? Circuit breaker?
If the breaker trips when nothing is turned on it could be a mouse problem. If it only trips when certain lights or appliances are turned on one of them is probably the reason.If it trips when nothing is being turned on or off something is getting hot. You should then have qualified electrician look at it. Hope this is usefull.
Does it run for a brief period then shut off? Could be a capacitor getting ready to fail. Could be getting hot. Is it tripping the circuit breaker?
No, the 50 amp breaker should not be getting hot with a 17 amp load. Shut the service off at the disconnect and check the bolts that tighten the breaker to the distribution's bus bars. Check the tightness of the load side of the breaker. if all of these connections are tight then change the breaker out for a new one.
Yes, it does the same thing as a GFI but also detects if there is an arc in the circuit, frayed wire, plug not in all the way, something that could possible cause a fire.
1. No power coming to your switch. Check your circuit breaker. If it is tripped, you have a "short" somewhere in the circuit. You will have to isolate the circuit. If it's not tripped, go to step 2... 2. A bad switch - Which you already replaced. You might want to check (use a voltmeter) to see if you are getting incoming voltage on your switch. If you are, go to step 3. If there is no power, it means you have a broken wire somewhere in between the switch and the breaker panel. 3. An open wirefrom the the switch to the ceiling fan electrical box. Again, check by using a voltmeter to confirm that the wire on the ceiling fan is getting power when the switch is "ON". If you are getting power go to step 4... 4. Bad ceiling fan - Removed and replace. Note: An open neutral wire (white wire) can also be the cause of the problem. Consult an electrician if you are not sure what to do.
For the entire circuit to go out, the breaker has to trip. The breaker tripping is what causes the loss of power to everything pulling power from that circut. Any single power surge at any point along the circut can cause it. If you have experienced what you are questioning, I suggest you have an electrician take a look at your wiring. You may have serious issues. Breakers a designed to protect the wiring from getting too hot. It's a safety feature for your appliances, your home and those who live in it.
Are any of the outlets OUTDOORS? If so, and if an outlet is getting wet, it will trip the GFIC immediately. If that's not it, unplug everything, reset the GFI and see what happens. If it still trips, make certain that the wires aren't getting wet somewhere. If THAT'S not helpful, replace the GFI.