0
You are getting 110 volts after the circuit breaker but only 50 volts at breaker why?
Wiki User
∙ 14y ago
you have a magic power-generating CB find out how it works and you should make a fortune.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Why am I only getting 120 volts from a 30 amp breaker that should be feeding 220 volts?
I assume you have a 30 amp two pole 220 volts breaker. Check the voltage source. If the source voltage is 220V, but out let voltage is 120 then the breaker must be faulty, a high resistance or partial open circuit could have caused the reduced voltage at the breaker outlet.
How many watts can be on a 15amp breaker?
At 120 volts a 15 amp breaker can be loaded to 1800 watts before it will trip. If it is a continuous load then the electrical code states that it is only allowed to be loaded to 80%. This will be 1800 x .8 = 1440 watts. If the voltage is not 120 volts use the following equation Watts = Amps x Volts. Amps being the breaker size that is to be used.
Where is the circuit breaker located on a 1967 Cadillac Fleetwood?
There is only one circuit breaker to my knowledge and it is for the power windows. I have a 1968 Fleetwood and it is very similar. What exactly is the problem?
What size ciruit breaker needed to run a 110v heater 500 watts?
That will draw about 9 amps at 120V. A 15 amp breaker if the circuit conductor is #14 or 20 amp breaker if the circuit conductor is #12. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed. Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Christmas light are causing the 15amp circuit breaker to trip and Circuit Panel is full Can I upgrade to a twin circuit breaker without installing a subpanel?
Your only hope is that someone wired the box not to code and that there are two wires going into the offending breaker. If you can't separate wires you can't distribute the load.
Why am I only getting 120 volts from a 30 amp breaker that should be feeding 220 volts?
I assume you have a 30 amp two pole 220 volts breaker. Check the voltage source. If the source voltage is 220V, but out let voltage is 120 then the breaker must be faulty, a high resistance or partial open circuit could have caused the reduced voltage at the breaker outlet.
Where is the circuit breaker for a hot water heater?
The best way to determine which circuit breaker is for the water heater is with a voltage meter, It is suppose to be only one circuit breaker, but in a faulty application it could be two breakers
Can multiple circuits be connected on one breaker?
Multiple wires can be connected to one breaker but the one breaker IS a circuit. As long as the load is not more than 80% of the breaker capacity (example: a 20 amp breaker can only have 16 amps or 1920 watts at 120 volts) then by code as long as the load is not a specialty outlet of some sort, you can have as many outlets you want.
How many watts can be on a 15amp breaker?
At 120 volts a 15 amp breaker can be loaded to 1800 watts before it will trip. If it is a continuous load then the electrical code states that it is only allowed to be loaded to 80%. This will be 1800 x .8 = 1440 watts. If the voltage is not 120 volts use the following equation Watts = Amps x Volts. Amps being the breaker size that is to be used.
Why am I only getting 1.5 volts max to the rear window defogger when I should be getting 6 volts I have 12 volts going into the def. switch and 6 volts leaving the switch.?
lol. 12v in, only 6 out. looks like your switch is eating 6 volts. Get that out of there. then the other volt drops should come into check. You should only have a .5v total volt drop in the whole circuit; after that problems start to pop up.
Where is the circuit breaker located on a 1967 Cadillac Fleetwood?
There is only one circuit breaker to my knowledge and it is for the power windows. I have a 1968 Fleetwood and it is very similar. What exactly is the problem?
Where are all the controls on most circuit breakers?
The only control on a circuit breaker is its on/off/reset lever or button.
Where is power window circuit breaker for 1989 Toyota Cressida?
Not circuit breaker only fuses in cars that are used. Driver side kick panel 7.5a gauge fuse check it fist.
What size ciruit breaker needed to run a 110v heater 500 watts?
That will draw about 9 amps at 120V. A 15 amp breaker if the circuit conductor is #14 or 20 amp breaker if the circuit conductor is #12. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed. Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What size breaker you would use for a 110 volt window air conditioning unit?
Breaker sizing is dependant on what the load amperage is that the breaker is connected to. If the amperage is not given but just the wattage, use this equation I = W/E. Amps = Watts/Volts. This air conditioner unit should be on a dedicated circuit receptacle. On these types of loads the conductor can only be loaded to 80% of the conductors rating. So a 15 amp breaker times 80% = 12 amps or Watts = Amps x Volts, 12 x 120 = 1440 watts. A 20 amp breaker times 80% = 16 amps or Watts = Amps x Volts, 16 x 120 = 1920. Once the breaker is sized remember to use the correct wire size to correspond with the amperage of the breaker.
What is a circuit breaker for?
The circuit breaker obviously breaks the circuit but only in an attempt to stop a surge of electricity going through your house and possibly hurting you if you're using an appliance, or popping light bulbs and most likely starting a fire.
Christmas light are causing the 15amp circuit breaker to trip and Circuit Panel is full Can I upgrade to a twin circuit breaker without installing a subpanel?
Your only hope is that someone wired the box not to code and that there are two wires going into the offending breaker. If you can't separate wires you can't distribute the load.
