answersLogoWhite

0

The line side is where the source of the voltage is connected. The load side is where the device being switched is attached. In the case of a light switch the line side would connect to the house power and the load side would be the bulb.

The switch is usually inserted in the line carrying the load (or black wires). As it it common to use 12-2 wiring to run from the device being switched to a switch on the wall, the return wire can be colored white. A electrician places an identification on the wire to signal that it is a "hot wire" even though it is white. Typically the electrician will wrap the white wire with black tape for about 1 inch to indicate this. A white wire is normally considered to be neutral if it is not identified as a "hot or load wire".

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Natural Sciences

When wiring an in-line switch does it go on the hot or neutral side?

The switch should always be on the HOT side. This way, when the switch is OFF, the light fixture is SAFE. Otherwise, you would have a HOT fixture with no clear return path when the swith is OFF -- very dangerous.


Which is the load side on a double pole switch?

The load side of a double pole switch is the side where the outgoing electrical current flows to the connected device, such as a light fixture or appliance. It is typically opposite to the line side, which is where the incoming electrical supply is connected.


How do you wire one light and one GFCI and another light light and fan with two switches and one power line?

Connect the incoming power to the line side of the GFCi outlet. Now run another wire connected to the line side of the GFCI outlet from the GFCI outlet to the switches. Power one of the switches and use that switch to turn on the 2 lights. Run power from that switch to another switch and use that switch to send power to the fan. Mount both switches in a double pole switch box. If the light above the sink has an outlet on it then you will have to connect power going to that light on the load side of the GFCI outlet. If not then just connect it to the line side.


How do you wire a switch outlet combo circuit to an existing 3 way light switch?

A switch is just a break in your hot wire. Your incoming power is usually on the bottom of the switch. Hook that one up to the hot side(gold in color) of the receptical and either pull the other wire out or snip the end off that is exposed and put a wire nut on it. Now you have to have a neutral wire(white). If there's one in there that was not hooked to the top of the switch then hook it to the silver screw of the recep. If one is not in there you'll have to bring one to it and you'll be good to go.


How do you connect a main switch?

The line supply connects to the top terminals of the switch and the load connects to the bottom terminals of the switch.

Related Questions

How do you wire a 2 pole 208volt motor switch?

The switch will have two termination points at the top or one side called the line side of the switch. The corresponding bottom or other side of the switch will be called the load side of the switch. Terminate the two wires from the distribution breaker to the line side of the two pole switch. Terminate the motor to the two terminals on the load side of the switch. On a motor switch there should be a place where an overload protection can be screwed in. Order the overload heater element to the sizing of the amperage on the motor's nameplate rating.


Where is the low pressure switch on a 1998 Chevy lumina?

The low pressure switch is mounted near the ac compressor. It is a two wire switch mounted in the low side line.


Where is the fuel reset switch for a 2003 Chevy Malibu?

Behind the fuel line on the right side of the motor.


Where is the low pressure switch for ac on a Toyota sienna?

It is located on the left side of the engine on the larger line.


How do you make a diagram of a battery and a bell?

Use the symbols for a battery, switch and bell and connect them together with a line starting at one side of the battery. From the battery series connect the switch and bell and then a line back to the battery.


What is the recommended wiring diagram for a 60 amp disconnect switch?

The recommended wiring diagram for a 60 amp disconnect switch typically includes connecting the power source to the line side of the switch and the load to the load side of the switch. It is important to follow the manufacturer's instructions and local electrical codes when wiring the disconnect switch.


How do you install an on off switch from an existing wire?

If you are asking how to add a switch to a lamp (or other load device) cord, simply cut the line side of the cord and connect to the switch terminals. ----mikey


99 harley softail brake light switch location?

the front switch is inside the handlebar right controll, the side the lever is on. you have to take this apart to se it, 2 torx screws, the back switch is located i n the brake line on the line to the rear caliper.


When wiring an in-line switch does it go on the hot or neutral side?

The switch should always be on the HOT side. This way, when the switch is OFF, the light fixture is SAFE. Otherwise, you would have a HOT fixture with no clear return path when the swith is OFF -- very dangerous.


Where is the brake switch located on a 1984 peterbilt 359?

The brake light switch is located on an aluminum air line junction block. The air line block is directly forward of the steering column on the cab side by the firewall. There is an access panel on the engine side of the firewall that gives you access for replacement.


Where is the low pressure switch for air conditioning 2004 ford F150?

On the accumulator, which is on the low side line at the firewall on the passenger side just below the battery. The low pressure switch is a two wire connector which faces the front of the vehicle.


Where is the ac low pressure switch for recharge located on a 2002 chrysler voyager?

IT is on the return line located on the passenger side firewall