0
What else can I help you with?
Which lens filter grades are acceptable for use when performing arc welding procedures?
which lens filter grades are acceptable when arc welding
What are applications of explosion welding over conventional welding?
The biggest application of explosion welding is the cladding of flat plate.
What does a Welding Inspector do?
A welding inspector spends lots of money getting exam qualifications and then re-sitting the same exams every five years for the privilege of sitting on his a--e at home most of the year waiting on the phone to ring ^^^^ The above was most likely written by an out of work welder (waiting at home for a council call) that became unemployed due to the problems that were encountered by crossing paths with a welding inspector that performed their duties with due diligence in regards to reviewing welder certifications (probably out of date for the above, if any), welding procedures (if any), approved fabrication drawings (probably hand drawn on a beer napkin), appropriate electrodes and welding equipment (chromed dental floss and a hair dryer from Tesco will not be acceptable), proper materials and fit up (scrap iron and rough guesses on dimensions most likely), industry and welding code approved welding practices (unlike the slop normally put in at their own manse and manor), failure to pass visual and non-destructive testing (Seeing through the weld in 3 spots is NOT acceptable in any code, thank you) and a myriad of other failures by the above poster that were easily spotted by the welding inspector. try this instead: http://www.weldmyworld.com/blog/2011/11/what-does-a-certified-welding-inspector-actually-do.html
What are two types of ac arc welding machines?
Two common types of AC arc welding machines are the transformer-based machines and inverter-based machines. Transformer-based machines use a transformer to step down the voltage and provide a stable arc, making them suitable for various welding applications. Inverter-based machines, on the other hand, use advanced electronics to convert the input power into a high-frequency output, allowing for greater efficiency, portability, and control over the welding process. Both types are widely used in different welding scenarios based on their performance and application needs.
What is horizontal welding position?
Look at a wall. Imagine welding on that wall from left to right or right to left. That is horizontal welding.
Which lens filter grades are acceptable for use when performing arc welding procedures?
which lens filter grades are acceptable when arc welding
What are applications of explosion welding over conventional welding?
The biggest application of explosion welding is the cladding of flat plate.
What does the 2 stand for in E48024 weldind?
In E48024 welding, the "2" indicates the weld's position classification according to the American Welding Society (AWS) specifications. Specifically, it denotes that the weld is suitable for use in all positions, including flat, horizontal, vertical, and overhead. This classification helps welders understand the versatility and application of the particular electrode in various welding scenarios.
What is the difference between welding engineering and welding technology?
Welding technology is the study and application of the many processes of joining various metals. Welding Engineering is a far deeper study and application into the individual characteristics of each metal. A welding engineer will decide what metals are used in a project and what process to weld those metals. Weld techs will usually just receive blue prints and weld as instructed. Welding technology is usually a 2 year degree, and Welding Engineering is a 4+year degree.
What does s8a6 indicate in weld?
In welding, "S8A6" typically refers to a specific classification of a welding electrode or filler material. The designation may indicate the type of material, its mechanical properties, and its suitability for various welding processes. For example, "S" may denote a specific alloy or coating, while the numbers represent particular characteristics such as tensile strength or application conditions. Always consult relevant standards or specifications for precise meanings.
What are Hobart welders and what they entail?
Hobart welders is a particular brand of welding equipment. You can take a look at hobartwelders.com and browse at all the welding equipment they offer.
What is efsw pipe?
What is the difference bitween EFSW and SAW welding process. Whether SAW process is acceptable inplace of EFSW.
Welding procedure specification?
A Welding Procedure Specification (WPS) is a formal document describing http://www.answers.com/topic/welding procedures. According to the http://www.answers.com/topic/american-welding-society-1 (AWS), a WPS provides in detail the required welding variables for specific application to assure http://www.answers.com/topic/repeatability by properly trained http://www.answers.com/topic/welder and welding operators. The American Society For Mechanical Engineers (ASME) similarly defines Welding Procedure Specification (WPS) as a written document that provides direction to the welder or welding operator for making production welds in accordance with Code requirements.
What tack wlding size and spacing is needed in relationship to material thickness?
The tack welding size and spacing needed for a particular material thickness can vary, but a common guideline is to use tack welds that are approximately 1.5 times the material thickness. The spacing between tack welds should be around 3-4 times the material thickness, depending on the specific welding application and joint configuration. It's always important to refer to welding codes, standards, or consult with a welding engineer for specific recommendations.
What is the difference between pressure and fusion welding?
Pressure welding uses pressure to create the bond between two materials, while fusion welding relies on melting the materials to create the bond. In pressure welding, the materials are pressed together under high pressure, while in fusion welding, the materials are melted together through the application of heat.
How many kgs of welding rod consumed in a linear foot?
The amount of welding rod consumed in a linear foot depends on several factors, including the type of welding process, the size and type of rod used, and the specific joint configuration. Generally, a rough estimate for arc welding can be about 0.5 to 1 kg of welding rod per linear foot. For precise calculations, it's essential to consider the specific application and welding parameters.
How is the size of welding tip indicated?
The size of a welding tip is typically indicated by its diameter, which is measured in either millimeters or inches. For example, welding tips may be labeled as 0.020", 0.030", or 1.0 mm, depending on the specific application and type of welding process used. Additionally, some manufacturers may use a numbering system to designate tip sizes, which corresponds to the gas flow and application needs. Always refer to the manufacturer's specifications for the correct size and usage guidelines.
