0
Troubleshooting 40 year old outside wiring to light fixture?
I live in a 40 year old house that has a white and black wire coming out of outside wall next to front door. No ground wire. Wires went to an old lantern style light fixture which stopped working. Checked inside light switch and is good. Measured 247v ac on outside white and black wires (with power to it off). Wired new light fixture (fixture and bulb tested as good) to the wires but lamp didn't work. Do I need an electrician?
David Meis
Yes
Douglas Joseph
Add your answer:
Earn +20 pts
How can I switch the light fixtures in my bathroom?
Switching a light fixture requires the following steps. First, remove the old fixture. Second, you must disconnect the wiring. Third, a junction box must be installed. Finally, a new fixture must be installed. Detailed instructions can be found here: http://www.diynetwork.com/how-to/replace-a-bathroom-light-fixture/index.html
How do you wire plunger lamp holder of fluroscent light fixture?
It sounds like you are describing either a slimline or dc recessed base type of fluorescent fixture. There is a wiring diagram on the ballast of both of these types of fixtures. Do your wiring the same as what is shown and you will have no problem.
How do you access the wiring in a recessed light?
There will always be a way to dismount the fixture. Look for some screws, they are usually hidden from sight.
Can you put a keyless light fixture on a pier?
No, they are not designed to be used outside and can only be used inside.
Wiring Up a Light Fixture?
Wiring Up a Light FixtureWhen remodeling a dining room, the light fixture can become a hazard if it is hung low enough. Banging one's head on a chandelier or heavy light cover hurts. If a light bulb breaks, it can become dangerous with broken glass in the eyes and under the feet. Wiring up a low-hanging light fixture takes a attention to a few details.Remove the table and chairs so access to the light fixture chain is unhampered. Set up a stepladder close enough to the fixture that it is easily worked on without the person leaning away from it. If the light covers are in the way, remove them to a safe area. Determine how much to raise the light fixture so people can walk under it safely.For raising the fixture temporarily, use a piece of baling wire or heavy construction wire. Place the wire through two of the chain links and lightly twist with a pair of pliers. When the work is over, remove the wire and lower the light fixture.If permanently raising the fixture is desired, purchase a connector link from the DIY store that matches the light fixture chain. As with the wire, attach the connector to two of the links and leave in place.This can be done with any light fixture in the home, on the patio, entryway or porch. For lights hung with cable, use a hose clamp spray-painted to match the cable. Do not over-tighten.
How do you hook up outside light fixture that has black white green to house wiring with only black and white?
If your house wiring is encased in armoured (metal) sheathing back to the panel, then you can secure the green ground to the ground screw in the box. Make sure the armoured cable connector is tight on the box. This should ground the light back to the panel. If you are on "knob & tube" I would suggest thinking about re-wiring the house.
Is a light bulb considered a fixture?
A fixture is what the light bulb goes into.
When wiring a light fixture does black go black and white on white?
If these are all the wires you have then this would be a great assumption. It assumes also that everything before the fixture is wired correctly and with commonly used color schemes.
Can faulty electrical wiring cause light bulbs to burn out quicker?
If light bulbs are burning out quickly the light fixture could be getting too much electricity due to faulty wiring. They could also burn out due to a loose wire or screwing the light bulb in too tight.
How do you change the ballist in a light fixture?
Ballasts can be quite different even if you order a replacement part for a specific fixture. You need to follow the wiring diagram on the new ballast. If this is confusing or not easy to follow, you need a competent electrician to do this for you.
How do you spell fancy light fixture?
The correct spelling for a fancy light fixture is "chandelier."
How do you wire a 220 volts light?
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
