What's the different between an Ethernet bridge and a switch?
The difference between an ethernet bridge and a switch is that the bridge only has two ports, while the switch has multiple ports. When there is a lot of traffic going through the ports, the bridge traffic may get tied up or crash often because there are only 2 ports for information to travel back and forth.
Unlike switch, bridge has the ability to connect lan with different IP subnet even different class.
Ethernet switches are used to make possible communication between different network meaning, switches create networks. Also switches use different mechanism of forwarding communication between computers as well as it does not share one channel for multiple computers.
how does each device work? what are the advantages of each? 1.switch 2.hub 3.bridge
A switch will allow you to share a single connection between multiple users with the switch handling the data between the different users. Netgear do reasonably priced switches (check out Amazon).
How do I switch my Ethernet internet link to my USB modem so I can use my Ethernet for different hookup?
put a usb in your laptop and transfer your ethernet file to the usb then place it where ever you want to have ethernet
Data link layer refers to things that happen within a single network; that's what a switch does. Only a router (or equivalent device, which I would still consider a "router") is able to connect different networks.The different networks may use the same technology (for example, Ethernet and Ethernet), or different technologies (for example, Ethernet and Wi-Fi); a switch is only able to connect parts of a single network that use the same technology (often this… Read More
PC1 to Switch, Switch to R1, C2 to R2
In the olden days you would use a bridge because hubs were one collision domain. The bridge was basically an expensive switch. Today on switches each switch port is on its own collision domain.
"RJ-45 Cross cable" is required for a direct ethernet connetion between two pcs between the same type of network devices (PC-to-PC, switch-to-switch, router-to-PC (Note: router and PC are LIKE devices, because both are DTE)) you use Crossover cable. to connect different type of devices (PC-to-switch, PC-to-router ..) you use Straight Through cable.
Ethernet switch fits on osi physical layer
Different between layer2 switch and multilayer switch
What could prevent a PING from being sent to the workstations when they are connected through the switch?
Firewalls prevent pings sometimes, especially Windows Firewall. Are they on the same switch or different switch? Is there a router / firewall / bridge between the switches? Are you sure it's a switch and not a hub?
Ethernet over E1 converter (also called E1 network bridge) is to transmit Ethernet data over E1 network (PDH,SDH network etc). The Ethernet port connect to terminal device,computer,Ethernet switch,Ethernet router etc. The device's E1 port connect to mail network(PDH SDH etc). E1 over IP (TDMOIP) is to transmit the E1 data over ethernet IP network. It transports the legacy E1 data through the existing Ethernet or IP network. The typical application is transmit voice and data… Read More
Via Ethernet cables, in the most typical case.
A hub connects various systems .hub acts as a server .hub can also be used as an individual system . A switch is a multi-pot network bridge .It will not be used seperately as a system.....
expands the amount of Ethernet cables you can have.
What type of cable is used to connect the Ethernet interfaces on a host PC to the Ethernet interfaces on switch?
An ETHERNET CABLE.
If you don't have enough ethernet sockets in a router, you can plug a switch or a hub into the socket. The hub or switch will supply support for additional ethernet cables.
The router is the brains of the network, it hands out the IP address's to all the devices and controls where the different information needs to go. All the switch does is route the calls to the right devices. If you talking about an Ethernet Switch then all it is is a smart hub. It's like a switch board operator on your phone, if computer 1 want's to talk to computer 3 then it routes… Read More
The standard Ethernet cables (UTP) basically limits the maximum distance between hubs, or between switches, or between a hub and a switch, to about 100 meters. If you use a longer cable than that, the signal will degrade too much, and the network may become unstable. The standard Ethernet cables (UTP) basically limits the maximum distance between hubs, or between switches, or between a hub and a switch, to about 100 meters. If you use… Read More
Connect one end of the cable into your computer and the other end into the Ethernet hub or switch.
The ethernet cable, ethernet switch or WiFi.
Yes, more than one Ethernet switch be connected to a network. Typically care must be taken as not to create loops in one's network.
You can have a maximum of four hubs between any two hosts (or from a host to the next switch).
Yes. The switch is acting as a "hub" between the various clients on the network.
Yes the switch is called a router and it can be wireless or wired with ethernet cables. I use my wireless router as a wired router because it also includes four ethernet cable connections in the back.
An Ethernet switch can not fulfill the role of a router, unless it be a "layer 3 switch" also known as "multilayer switch", which has capabilities of both a switch and a router - and is more expensive than either (mainly because it is optimized for handling lots of traffic, quickly). For a small network, you don't really need a router. Routers are used to divide larger networks into smaller subnets, for efficiency, security, and… Read More
Ethernet switch,cut through,crossbar,cell backbone,store and forward, back presser, atm, LAN
What type of cable is used to connect the Ethernet interface on a switch to the Ethernet interface on a router?
To the switch the router is just another host, so it connects with a straight Cat 5 or Cat 6 cable.
A router, switch or hub can be at the center of an ethernet network.
Hubs and Switches make 1 ethernet connection out of as many is on the hub or switch.
The Cisco Power over Ethernet (PoE) switch allows connectivity to ethernet-powered devices including wireless access points, video cameras, and Cisco IP phones.
A router will typically support between 4 and 8 ports. For additional ports, a standard Ethernet switch can be connected to one of the ports.
A regular Cat 5e or Cat 6 RJ-45 straight-through Ethernet network cable.
You can use a switch to connect different pieces of equipment. For example, a standard ADSL router only has a port for a single Ethernet cable. If you want to connect 2 or more computers to the Internet, you can use a switch. In this case, the ADSL router and each computer connect to the switch, via a standard Ethernet cable. If you don't have an Internet connection, you can still set up a home… Read More
No. Ethernet is standardized, you can use any brand of Ethernet router (or switch) with any computer brand.
we use straight cable to connect between the router and switch as router and switch are different devices.
Whart are the switch and bridge port characteristic of a layer two spaming-tree network that is fullycoverged?
a. All switch and bridge ports are in the forwarding state. b. All lkswitch and bridge ports are in the stand by state. c. All switch and bridge parts are assigned as either root or designed. d. All switch and bridge ports are in either the forwarding or blocking state. e. All switch and bridge are either blocking or looping.
fast ethernet port
Yes, in fact, that is the most common thing to do - hook an Ethernet or FastEthernet port, in the router, to a switch.
It depends; if topplogy is intended in terms of Local Area Network (LAN), most Ethernet LANs use the same topology which is hub and spoke, where Ethernet switch(es) act as the hub and the spokes are hosts (PC's, servers, printers, IP phones, etc.). If topology is meant in terms of different technologies, e.g. Interconnecting an Ethernet network to a SONET or MPLS network, then a router is required between the two. Another possibility is transporting… Read More
The "switch" on an electric guitar generally switches between the pickups, for different sounds.
Actually no difference, bridging is one of functions supported by modern routers (wireless switches).
Ethernet Cross over cable
In STP, first a central switch (or bridge, as it it called in STP) is selected - the "root bridge". All other switches calculate the shortest path to this root bridge.
In the case of ethernet, you need a "crossover" ethernet cable connected between two regular ports or a regular ethernet cable connected to an "uplink port" on one switch and a regular port on the other. Uplink ports are sometimes called "MDI" ports. Both types of cable are available at most computer and office supply stores.
A switch is multiple ethernet port, where connected more than one Pcs and get shareing data, application each other. it is called network switch.
Buy another cable they are cheap. You can always plug in the PS3 and unplug whatever was and switch back and forth like you would if you needed to purchase a router. That does work better if you at least have two ethernet cables and only need to switch at the modem between PS3 cable and Computer cable unplugging the device you are not using and then plug in the one you want too.
This refers to switching at layer 2 of the OSI reference model, for example, Ethernet. A switch looks at the MAC address of each Ethernet frame ("packet", you might say, but at this level the correct name is "frame"), and if it knows that this MAC address is connected at a certain port, the switch will send the information out ONLY through that port. This refers to switching at layer 2 of the OSI reference… Read More
gear switch is operated manually while changeover is automatic