0
What areas can Differential pressure transmitter be used in？?
zhei thang
1: Guage pressure measurement by supply the HIGH side and venting the LOW side to the atmosphere
2: Measurement of level of open tank by connecting the impulse line at the bottom of the tank to HIGH side and venting the LOW side
3: Measurement of level of closed tank with liquid and Gass interface by connecting the the impulse at the bottom of the tank to HIGH side and the impulse line at the top of the tank to LOW side of the transmitter capsules
4': Measurement of Vacuum by connecting the impulse line in LOW side and venting the HIGH side to the atmosphere
5: Measurement of absolute pressure by supply the HIGH side and blinding or blocking the the LOW side
zhei thang
Add your answer:
Earn +20 pts
What instrument is used to predict wind speed?
A series of barometers can be used to predict wind speed and direction. Wind will move from higher pressure areas to lower pressure areas. The higher the pressure differential the higher the wind speed will be.
What is a wet leg?
Wet legs are used on differential pressure measurement where both sides are filled with liquid. Exception is level measurement in a pressurised vessel (boilers). Dry legs are used where the low side is exposed to atmosphere using a DP transmitter for level measurement in a open tank.
which areas can be used for as the differential pressure transmitter?
1: Guage pressure measurement by supply the HIGH side and venting the LOW side to the atmosphere 2: Measurement of level of open tank by connecting the impulse line at the bottom of the tank to HIGH side and venting the LOW side 3: Measurement of level of closed tank with liquid and Gass interface by connecting the the impulse at the bottom of the tank to HIGH side and the impulse line at the top of the tank to LOW side of the transmitter capsules 4': Measurement of Vacuum by connecting the impulse line in LOW side and venting the HIGH side to the atmosphere 5: Measurement of absolute pressure by supply the HIGH side and blinding or blocking the the LOW side
How are isobars used to show pressure centers?
Isobars are lines that join areas of the same pressure. Low pressure areas are circular, so the isobar lines will form a loop and join ends. The varying pressures can now be seen as concentric rings, with the lowest pressure at the center of the circle.
What is a tank circuit used for?
A tank circuit is used on a radio transmitter. It is an electronic circuit that is used to tune a specific frequency. The tank is made up of two components, an inductor and a capacitor. The two components are connected in a parallel with each other. This is where the term "tank" comes from. Used in a radio transmitter, it is tuned for maximum RF (radio frequency) output on the frequency the transmitter is tuned to.
What instrument is used to predict wind speed?
A series of barometers can be used to predict wind speed and direction. Wind will move from higher pressure areas to lower pressure areas. The higher the pressure differential the higher the wind speed will be.
How does a 3 way manifold valve work?
If you mean by three-valve manifold, then If you apply excessive pressure to your differential pressure transmitter, you could damage your instrument. This is known as over-ranging the transmitter. A three-way manifold valve is a device that prevents the instrument from being over-ranged. It also allows the isolation of the transmitter from the process loop (an option which could be used generaly for maintenance or re-calibration or fitting new equipment). It consists of two blocking valves and one equalizing valve. The blocking valves are for both high pressure and low pressure sides. During normal operation, the equalizing valve is closed and the blocking valves are open. When the transmitter is put into service, care should be taken to ensure that the high pressure is never applied to one side of the Differential Pressure Transmitter. To put a DPT into service using the Three-way manifold valve is to first close all valves. Then, open the equalizing valve to ensure the same pressure will be applied on both sides of the transmitter. Therefore you will have a zero differential pressure. Next, the high pressure block valve is opened slowly (to check for leakage from both sides of the transmitter). The equalizing valve is closed and this locks the pressure from both sides of the transmitter. Now open the low pressure block valve to apply the process pressure to the low pressure side and establish the working of the DPT.
What are the field instruments used in power plants?
Temperature: Thermocouple, RTD, Temperture Transmitter. Flow Transmitter, DP ransmitter, Pressure Transmitter, Pressure switch, Radar level Transmitter, PLC system, Woodward Governor, Ultrasonic flow transmitter. Relay, Control Valve, ON/OFF valve.
What is a wet leg?
Wet legs are used on differential pressure measurement where both sides are filled with liquid. Exception is level measurement in a pressurised vessel (boilers). Dry legs are used where the low side is exposed to atmosphere using a DP transmitter for level measurement in a open tank.
What Differential Pressure Transmitters Do?
Differential pressure transmitters were originally designed for use in pipes to measure pressure before and after the fluid encounters a filter, pump, or another interruption in flow. Standard differential pressure transmitters come with two process connections arranged side by side to measure the drop in pressure (d) between the higher and lower points (H and L, respectively, in Figure 1). Classic differential pressure transmitters can also measure flow rates. It wasn’t long before people realized that differential pressure measurements could be used to determine liquid level as well.
What is the primary function of a pressure differential valve used in a hydraulic brake circuit?
To send more pressure to the front wheels, where it is needed.
which areas can be used for as the differential pressure transmitter?
1: Guage pressure measurement by supply the HIGH side and venting the LOW side to the atmosphere 2: Measurement of level of open tank by connecting the impulse line at the bottom of the tank to HIGH side and venting the LOW side 3: Measurement of level of closed tank with liquid and Gass interface by connecting the the impulse at the bottom of the tank to HIGH side and the impulse line at the top of the tank to LOW side of the transmitter capsules 4': Measurement of Vacuum by connecting the impulse line in LOW side and venting the HIGH side to the atmosphere 5: Measurement of absolute pressure by supply the HIGH side and blinding or blocking the the LOW side
What is the function of manometers?
One of ends of the tube is used for pressure measurements, the other can be left open to the atmosphere to measure static pressure, or can be attached to the low end of a pressure system to measure differential pressure.
What type of radio transmitter was used on the ship Titanic?
The Titanic used a Marconi designed spark transmitter.
Could incandescent light be used for a fiber optic transmitter?
Incandescent light cannot be used for a fiber optic transmitter. This is because incandescent light is too slow for such a transmitter.
Why power amplifier used in FM transmitter?
Amplifier is used in an FM transmitter to increase the level of a signal suitable for transmission
The lines of constant pressure shown on the surface pressure diagram are called?
Line of constant pressure shown on the surface pressure diagram are called isobars. Isobars show areas of high pressure and areas of low pressure. The surface pressure diagram can be used to predict weather patterns.
