0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What are Breaker point contacts are made of?
Breaker point contacts are made of silver plated copper.
What is the contract breaker points setting for a Nissan 1400 pick-up?
.020 or half the spark plug gag.
How do you replace a 15 amp breaker in the circuit box?
The breaker will have a black wire connected to it. Turn off the main breaker and then disconnect that black wire from the breaker. The breaker will snap into the main bar. Remove the breaker and install the new one. Reconnect the black wire to the breaker and then install the cover and turn the main breaker back on.
Can a Siemens breaker push on be a replacement breaker for a Westinghouse breaker?
only if listed in the panel board
A GFCI device in a breaker is intended to?
A GFCI device in a breaker is intended to trip the breaker open when a ground fault is sensed in the circuit that the breaker is protecting.
The function of the condenser in a breaker points ignition system is to?
The function of the condenser in a breaker points ignition system is to keep the points from sticking together. If the points stick together during ignition it could cause the points to burn up. The condenser sends a signal to the points and then takes the signal away to make the points separate.
What does dwelled?
The number of degrees the breaker cam rotates from the time the breaker points close until they open again.
What are Breaker point contacts are made of?
Breaker point contacts are made of silver plated copper.
What is contact breaker points gap Austin mini?
0.12-0.15
What does dwell mean?
The number of degrees the breaker cam rotates from the time the breaker points close until they open again.
How to isntall points and condenser on a Briggs and stratton engine 10hp model 243431 type 0123?
CLEAN AND ADJUST CONTACT POINTSRemove cover. Clean points with a carborundum contact point stone. Then insert a hard finished card or pied, of paper and close and open points. The paper will absorb any dirt or filings on the points. Adjust breaker points as follows:a. Rotate crankshaft until points open to widest gap.b.. Loosen lock nit illustrated below until it is just snug.c. Rotate breaker point screw to obtain .020" gap.d. When gap is .020" tighten locknut.e. Replace breaker box cover. Same for installation, just eliminate the cleaning. CLEAN AND ADJUST CONTACT POINTSRemove cover. Clean points with a carborundum contact point stone. Then insert a hard finished card or pied, of paper and close and open points. The paper will absorb any dirt or filings on the points. Adjust breaker points as follows:a. Rotate crankshaft until points open to widest gap.b.. Loosen lock nit illustrated below until it is just snug.c. Rotate breaker point screw to obtain .020" gap.d. When gap is .020" tighten locknut.e. Replace breaker box cover. Same for installation, just eliminate the cleaning.
What is contact breaker point?
If you are talking about points and condensor for your automobile they are located inside of your distributor located on you motor.
How many points must a team gain to win a set in volleyball?
For the first 2 games a team has to get 25 points, In the last game (tie breaker) a team has to get 15 points. In most situations you have to win by 2 points.
What is the contract breaker points setting for a Nissan 1400 pick-up?
.020 or half the spark plug gag.
How can a circuit breaker be made to work after it has opened?
put your dick in it
What is one main function of the condenser for engine?
To absorb voltage spikes or surges that occur when the breaker points open and close.
What happens if the end of a tennis match is tied?
You play a tie-breaker. This is usually 7 points if the games in the set is tied
