0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Introduction of chip thickness ratio and shear plane angle during machining?
shear plane angle is Eric siangco + hulian lastontas = shear plane angle
What are the functions of frame relay?
networking purpose
What can be derived from the shear force?
Shear force in a cantilever beam at the support due to a concentrated load is equal to the magnitude of the concentrated load (or sum of the loads) regardless of their position along the beam. Shear force in a cantilever beam increases linearly from zero at the free end to a magnitude of (wL) at the support, where w is the uniform load and L is the length of the beam.
What is the ratio of average shear stress to maximum shear stress for a circular section?
the average shear stress is 3/4 the maximum shear stress for a circular section
How does shear strength of fine sand effect by void ratio?
Shear strength of fine sand is determined by the angularity of the sand particles, the grading of the sand. These two features governs the critical state shear strength parameters of the sand. Density, however, dictates the peak shear strength of the sand. i.e. the denser the sand, the higher the peak shear strength. But the critical shear strength remain the same. The denser the sand, the lower the void ratio. Shear strength of fine sand is determined by the angularity of the sand particles, the grading of the sand. These two features governs the critical state shear strength parameters of the sand. Density, however, dictates the peak shear strength of the sand. i.e. the denser the sand, the higher the peak shear strength. But the critical shear strength remain the same. The denser the sand, the lower the void ratio.
Introduction of chip thickness ratio and shear plane angle during machining?
shear plane angle is Eric siangco + hulian lastontas = shear plane angle
Relationship between the shear stress and angle of shear?
Shear Stress divided by the Angle of Shear is equals to Shear Stress divided by Shear Strain which is also equals to a constant value known as the Shear Modulus. Shear Modulus is determined by the material of the object.
What is the relationship of shear angle and rake angle?
∅=45°+ α- β∅=shear angleα= rake angleβ= friction angle
What is the purpose of shear draperies?
The purpose of shear draperies is to allow light in while giving you the comfort of privacy.
Definition of hooke's law in shear?
shear stress (t) is proportional to shear modulus (G) x shear strain (h) or t = Gh where h is shear angle/length
What is the relationship between basic friction angle and residual friction angle of sandstone?
For rock, the basic friction angle is somewhat less than residual angle. The basic friction strength is that shear resiatance of two smooth surfaces. The residual shear atrength is that for two rough surfaces after long shearing. At residual state, the shear resistance almost keeps constant and no shear-dilation.
What angle should garden shear blades have?
90
What is the purpose of measuring taper angle of a taper plug gauge?
The purpose of measuring taper angle is to obtain taper angle
Is shear an adjective?
No, it is not. Shear can be a verb (to cut, remove wool, or to apply force at an angle) or a noun (cutting tool, shearing force). It can, however, be a noun adjunct in terms such as shear strain. *Not to be confused with the homophone "sheer" - adjective meaning transparent.
What is basic friction angle?
Friction angle or also known as angle of repose of soil is the subtended angle formed between the side slope with the vertical of a loose heap of the soil. This can also be determined by the triaxial shear test on soil conducted in laboratory.
What is complementary function in mathematics?
sin and cos functions are complementary..they vary by an angle of 90deg in their graph.. so thts wht i think it is..complementary functions are probably functions whch differ by an angle of 90 i their graph..
Why shear angle is given to press tool?
Cutting shear is given to punch or the die that function to reduce the necessary cutting tonnage by reducing effective area of shear ie creating scissor action for eg considering cutting paper with scissors we will start from one side and progres to other end but it press tool is moved perpendicular instantly have to contact whole sheet, when shear angle is given at the instant of contact only small line of contact is made, thus reducing force required for shearing.
