0
What else can I help you with?
How do you adjust the belt tension for the alternator on a 91' Honda Accord?
Loosen the upper and lower alternator mounting bolts. Turn the adjustment bolt on the lower left-hand side of the alternator. You should only be able to bend the belt 90 degrees at its longest run, in the middle. When done adjusting, tighten the upper and lower alternator mounting bolts.
How do you replace Chevy Cavalier alternator?
Remove the bolt on the lower front side and two more bolts on the rear of the alternator. Make sure all nuts are off the bolts. Do not loosen the bolts that hold the alternator together. Remove the belt. Now slide the alternator off the mounting bolts. Slide the new alternator onto the two seating bolts, then hand-tighten them. Then slide the next bolt through the alternator and into the engine block.Slide the new alternator onto the two seating bolts, then hand-tighten them. Then slide the next bolt through the alternator and into the engine block. Now tool-tighten all the bolts to secure the new alternator to the engine block.
How do you replace the alternator in 1988 Pontiac fiero?
It's two bolts. There is a top alternator bolt and an lower adjustment bolt. Loosen both bolts enough to slip off the alternator belt. Remove the bolts, and then slide the alternator down and under the car through the passengerside wheel well. Installation is the reverse of above.
How do you replace the alternator on a 2002 mountaineer?
V6 MODELS # Disconnect the negative battery cable # Remove the drivebelt # Disconnect the electrical connectors from the alternator # Remove the mounting bolts and remove the alternator V8 Models # Disconnect the negative battery cable # Remove the engine cover # Position the cruise control cable and throttle bypass hose asside # Remove the drivebelt # Disconnect the electrical connectors from the alternator # Remove the 2 upper stud bolts and the 2 upper alternator mounting bolts # Remove the 2 lower alternator mounting bolts and remove the alternator
How do you replace an alternator in a 1996 Geo Metro?
First you have to disconnect the power from the battery. Then you remove the belt,and all electrical connections. Then you take out the bolts holding it on the brackets and bring it out from under the car. - Disconnect Battery - Remove Air filter intake components. - Remove fuel hose to carb (maybe) - Remove 12mm upper alternator mount bolt - Dissconnect 10mm Alternator positive connection. - Dissconnect Alternator connector plug. - Remove 2*12mm lower alternator mount bolts. - Remove 2*10mm lower alternator shield bolts. - Remove 2*14mm exhaust pipe to manifold bolts. -Wiggle the old alternator out and the new in...trust, it works IF YOU INTENDED TO REPLACE THE ALTERNATOR BELT... - Slacken the underside 10mm main belt tension pulley to allow alternator belt R&R.
Where is the fuel pump in a 1991 ford escort located?
attach to the gas tank. Inside. Lower gas tank and need to get in the cylander and open it up.
How do you install lower control arm in 2000 suzuki esteem?
Locate the control arm under the vehicle. Attach it with mounting bolts. Put the bushings in place. Tighten the mounting bolts only when all bolts are installed. Connect the sway bar the lower control arm.
How do you replace the alternator on a 1995 Buick LeSabre?
Piece of Cake!! remove serpentine belt (search here for answer how to), remove the lower of 2 bolts from the alternator, loosen the upper, rotate the alternator up, remove the bolt. Install is the reverse.
How do you replace the alternator on a 1992 Mazda miata?
Main steps: * Unplug battery neg. terminal * Loosen alternator bolts, lower one (main) and the 2 for the tensioner * Remove the belt * Remove the wires to the alternator * Remove the bolts and take the alternator off * Put the new one, secure with main bolt and tensioner * put belt back and and tension it, tightening bolts * Connect wires back It will take about 1 or 2 hrs.
How do you tighten an alternator belt on a Toyota 4 Runner?
V6 4Runner has a 14mm bolt on the top of the alternator and a 12mm bolt on the bottom of the alternator. Loosen both of these bolts. Look through the drivers side wheel well and you will see another 12mm bolt below the alternator. This is your tension adjustment bolt. Tighten or loosen as needed. After proper tension is achieved tighten the upper and lower alternator mounting bolts you loosened earlier.
How do you replace the alternator on a 2000 Hyundai Elantra?
# Disconnect negative battery cable # Raise car and support it # Disconnect the wire harness from the alternator electrical connections # Loosen the alternator lower mounting bolts.Working from above loosen the upper adjustment lockbolt,back off the adjustment bolt swivel the alternator toward the engine and then release the drivebelt from the alternator pulley # Unscrew and remove the alternator upper and lower mounting bolts and washers then remove alternator from its mounting bracket
Where is the alternator fuse located on a 1991 Mazda Protege?
if you are standing on the passenger side facing the engine,it is on the lower left side.easy to change has two bolts
