Want this question answered?
Hello, It depends on what hardness do you want to test? The hardness of gems, one would use a scratch test. The Vickers hardness test was developed in 1921 by Robert L. Smith and George E. Sandland at Vickers Ltd as an alternative to the Brinell method to measure the hardness of materials. The Vickers test is often easier to use than other hardness tests since the required calculations are independent of the size of the indenter, and the indenter can be used for all materials irrespective of hardness. The basic principle, as with all common measures of hardness, is to observe the questioned material's ability to resist plastic deformation from a standard source. The Vickers test can be used for all metals and has one of the widest scales among hardness tests. These are just examples of hardness tests, there are many! You should find out what you want to test for and find the most suitable test. Hope I Helped
The hardness of rhenium is 7.0 on the Mohs scale. It has a hardness of 2450 MPa on the Vickers scale and 1320 MPa on the Brinell scale.
hardness
Hardness of uranium metal: Mohs hardness: 6 Brinell hardness: 2 400MN/m2 Vickers hardness: 1 960 MN/m2 Uranium is very hard and also very dense (19,05 g/cm3). Depleted uranium is used for artillery shells (also for tanks armour) to give it Armour piercing capability.
The hardness scale
In Vickers hardness test the for used is much lighter than the force used in Rockwell hardness test, The Rockwell hardness test is the considered to be the most routinely used technique to measure the hardness of materials because of its simplicity and because it does not require specific skills in order to perform it.
Hardness of ductile materials can be determined by following methods..... 1) Brinell Hardness Test 2)Vickers Hardness Test 3)Rockwell Hardness Test 4) Scratch hardness test
Hello, It depends on what hardness do you want to test? The hardness of gems, one would use a scratch test. The Vickers hardness test was developed in 1921 by Robert L. Smith and George E. Sandland at Vickers Ltd as an alternative to the Brinell method to measure the hardness of materials. The Vickers test is often easier to use than other hardness tests since the required calculations are independent of the size of the indenter, and the indenter can be used for all materials irrespective of hardness. The basic principle, as with all common measures of hardness, is to observe the questioned material's ability to resist plastic deformation from a standard source. The Vickers test can be used for all metals and has one of the widest scales among hardness tests. These are just examples of hardness tests, there are many! You should find out what you want to test for and find the most suitable test. Hope I Helped
It is estimated that the Vickers hardness of promethium is 617,8 MPa.
Minimum hardness of Mild steel is about 140 Vickers hardness.
The Brinell hardness of plutonium is 242, the Vickers hardness is 255.
I don't found the Mohs hardness of plutonium but: - the Brinell hardness is 242 at r.m. - the Vickers hardness is 255 at r.m. After a hardness conversion chart an equivalent Mohs hardness may be 3,7.
HV = 2.9 * Y Where HV - Vickers hardness Y - Yiekd stress in KG/mm2
The Brinell hardness of technetium is 112.The Vickers hardness of technetium is 151.
The Brinell hardness of technetium is 112.The Vickers hardness of technetium is 151.
Plutonium is a silvery metal.- Vickers hardness: 255 - Brinell hardness: 242 - Mohs hardness: cca. 3,7
http://www.gordonengland.co.uk/hardness/microhardness.htm