answersLogoWhite

0


Best Answer

Four Basic or Main Parts Of Stator :

1. Yoke(Outer Frame)

2.Main Magnetic Poles

3.Main Field Winding

4.Inter Poles

User Avatar

Wiki User

11y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What are the four main parts of the stator motor?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Engineering

When you dismantle an electric motor what do you see?

Main parts such as rotor and stator.


What is the main part of ac motor?

shaft, windings, ball bearings, armature, stator, commutator, brushes, terminals, case.


What is the main purpose of a single phase capacitor start induction ac motor?

A single-phase induction motor can run either way depending on how it's started because the stator field does not rotate. The starting winding, fed by a capacitor to produce a phase-advanced current, generates a small rotating field to start the motor going in the right direction. Once the motor has run up to speed it latches on to the main stator field, which can be resolved into two oppositely-rotating fields. The armature produces torque from only one of the rotating components.


Can you describe the procedure for overhauling a three phase induction motor?

The only preventive maintenance that can be done to electric motors by maintenance personnel is to disassemble the motor. The motors bearings can be cleaned and re greased or if sealed bearings that can be changed out for new ones. Remove any grease or dust build up from the stator with compressed air. The stator then should be washed out with a solvent that is specifically made for cleaning electrical equipment. Dry the stator making sure that the motor coils have room around them for air to flow. Dirt accumulations around coil wiring insulation is the biggest cause of motor failure. The coil wires need cooling air moving across them. With totally enclosed motors the cooling vanes on the outside of the motor need to be kept clean as they are the only means of removing the heat from the motor.


What are the methods of stopping a synchronous motor?

My experience with synchronous motors is in the operation of large rotating mills. In that case, the motors are decoupled from the load by means of an air-clutch, and main power is removed from the rotor and the stator. The motor coasts to a stop. If the motor is operated on a variable speed drive, it could be decelerated to very low speed before removing power.

Related questions

When you dismantle an electric motor what do you see?

Main parts such as rotor and stator.


What are the main parts of three phase motor?

Wire, bearings, rotor and stator.


What are the four main parts of a car's alternator?

The four main parts of a car's alternator are the regulator, rotor, stator, and diode bridge.


What there are there main parts?

stator and rotor.


What do you understand about the stator of an AC motor?

AC motor has two main winding components - stator and a rotor. Stator winding is stationary where as rotor winding is on rotating part.


What are the main parts inside the alternator?

*stator *rotor *regulater *rectifier


What is the main part of ac motor?

shaft, windings, ball bearings, armature, stator, commutator, brushes, terminals, case.


What are stationary part of dc motor?

The stationary part of any motor or generator is termed the 'stator', and the rotating part is termed the 'rotor'.The stator comprises the main frame (chassis), the magnetic circuit, and field windings.


What are the five areas of the keyboard?

what are the four main parts of a keyboard and their function what are the four main parts of a keyboard and their function what are the four main parts of a keyboard and their function


How many main parts does a four wheeler have?

How Many Main Parts Of Four wheeler


What are four main parts of a plant?

the four main parts are the root,steam,leaves,


Where are the main windings of an AC induction motor situated?

Front and rear.AnswerThey are located in longitudinal slots that are machined into the inner surface of the stator.