0
What are the points you will keep in mind about the concept of quality control and inspection if you are the quality systems manager of a rubber products manufacturing unit?
Wiki User
∙ 14y ago
what are the points you will keep in mind about the concept of quality control and inspecyion if you are the quality systems manager of a rubber products manufacturing unit?
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What does GMP stants for in manufacturing term?
GMP = "Good manufacturing practice".GMP is a set of practices and systems that have to be used in pharmaceutical industry (manufacturing, quality control, testing). These are general principles, not not prescriptive instructions.In United States GMP is enforced by the FDA.
What are the points you will keep in mind about the concept of quality control and inspection if you are the quality system manager of rubber products manufacturing unit?
Quality control (QC) is a procedure or set of procedures intended to ensure that a manufactured product or performed service adheres to a defined set of quality criteria or meets the requirements of the client or customer. QC is similar to, but not identical with, quality assurance (QA). QA is defined as a procedure or set of procedures intended to ensure that a product or service under development (before work is complete, as opposed to afterwards) meets specified requirements. QA is sometimes expressed together with QC as a single expression, quality assurance and control (QA/QC).In order to implement an effective QC program, an enterprise must first decide which specific standards the product or service must meet. Then the extent of QC actions must be determined (for example, the percentage of units to be tested from each lot). Next, real-world data must be collected (for example, the percentage of units that fail) and the results reported to management personnel. After this, corrective action must be decided upon and taken (for example, defective units must be repaired or rejected and poor service repeated at no charge until the customer is satisfied). If too many unit failures or instances of poor service occur, a plan must be devised to improve the production or service process and then that plan must be put into action. Finally, the QC process must be ongoing to ensure that remedial efforts, if required, have produced satisfactory results and to immediately detect recurrences or new instances of trouble.· In general, the application of the concept of Quality Control and Inspection for a rubber products manufacturing unit would consist of:Ø 1. Receiving Inspection - to assure the product/material received meets the required specifications before it is manufactured.Ø 2. In-process Inspection (On-going basis)- to assure the partsØ 3. Finished Goods Inspection (to ensure any secondary operations are performed to specifications and that product meets all requirements)Ø This is the inspection side. Keeping all of this in mind, the concept of quality is to ensure the product is manufactured correct the first time.a. Receiving Inspection: It means as a Quality systems manager the product or the material received from various sources should be tested or evaluated to know whether it meets the specifications. If not the Raw-material should be dismissed and not to be used.b. In process Inspection: This means the products have to be tested while on the production or while they are In-process. This will give the fair idea to the QA manager whether the products are generating the expecting outcome. If he thinks the rubber material doesn't producing the expected outcome it should be terminated immediately.c. Finished goods Inspection: This means the products have to be tested to assure 100% quality. The QC manager has to take the full in charge and pass the "QC test"The above said methods are critical and it should be followed strictly without which the product may not meet the specifications of Quality control and inspection. Zero-level defect must be assured to get 100% quality of rubber goods.
How do you Control the Production Quality of Shirt?
To control the production quality of shirt should start with the following aspects: 1. Fabric Inspection Fabric inspection is the first and also crucial checkpoint when producing shirts. Only qualified products can be passed into next process. Some fabric defects are difficult to eliminate, which will directly affect the quality of finished product such as spun yarn, soft sides, nep, hole, oil stain, etc. Fabric inspection can be divided into the following details: (1) Use the cloth inspecting machine to check each fabric under the standard illuminant lamphouse. Mark at the edge of the fabric if there are defects on that fabric. Judge to use or return these fabrics to supplier if there are many stains or unacceptable stains on the fabrics. (2) Color difference inspection: compare the same fabric with the color in the beginning, middle and end. Use the color card to check every piece of fabric color. (3) Shrinkage rate: shrinkage rate of fabric will directly affect the stability of shirt size. Oversize shrinkage rate is not so good for controlling the shirt size. (4) Fabric amount inspection: guarantee the fabric amount and complete the order according to the amount required. (5) Fabric structural inspection: check whether the tightness, thickness, density of fabrics meet the requirement or not. 2. Intermediate inspection There are many forms to inspect. According to the order of work process it can be divided into receiving inspection, process inspection and finished product inspection; according to the place of survey it can be divided into fixed inspection and flow inspection; according to the amount of inspection it can be divided into total inspection and sampling inspection. While the intermediate inspection of shirt processing mainly is combined with process inspection and flow inspection. Preventing the process defects such as seam type, seam distance and size which are not meet manufacturing technique. Prevent and control rejects effectively. (1) Process inspection Process inspection examines during the processing. Not only need they examine processing quality but also examine the factors which effects processing quality. The function is used to preventing rejects from producing and flowing into the next process. Process inspection can be divided into one by one step process inspection and several steps process inspection. One by one step process inspection can guarantee the processing quality while the workload is large. Shirt enterprises usually use several steps process inspection, and the checkpoints are mainly located in the critical process where the qualities are easy to fluctuate or there are big influences to end products qualities. Or there is a process which some rejects can not repair, like combined panels such as attach collar and attach cuff before process and unrepairable buttonholing before process, so semi-finished products must be inspected. (2) Flow inspection Flow inspection is also known as cyclic detection. It is the inspection which exclusive surveyors check in the workplace. Through the cyclic detection, labile factors in the productive process can be timely found and corrected. Not only does it prevents the rejects but also convenient for exclusive surveyors to guide the handlers. On the basis of the certain inspection way and cyclic times, when doing cyclic inspection, exclusive surveyors should check the quality of semi-finished product and finished product which related to process, the conditions which operator carries out, the conditions which ideas arranged in the process control chart and the conditions which waste defective products segregate. When sewing the shirts, every time we sew the semi-finished shirts, those must be intermediately inspected by the specialized person to guarantee the semi-finished shirts are qualified and the rejects will not passing to the next process. 3. Inspection of finished product Inspection of finished product is also known as the final inspection. It is a overall inspection before the products put in storage and it is the requisite measure to prevent the rejects leaving the factory. Inspection department issues the certification after inspect finished product. In clothing factories, the main inspections for finished product are end process inspections such as garment appearance, manner of packing, packing material, etc.
What is GMP training?
"GMP training is the education someone receives in good manufacturing practice, which refers to quality control testing." "Basically, GMP training refers to Good Manufacturing Practice. GMP is used in the maufacture of food, pharmecutical products and medical devices, to make sure that they are meeting high-quality standards."
What is production planning and control used for?
Production planning and control is used in the manufacturing industry. As the name suggests, it is used to plan and control the process of production.
What are the concepts of quality control and inspection of rubber products manufacturing unit?
In general, the application of the concept of Quality Control and Inspection for a rubber products manufacturing unit would consist of: 1. Receiving Inspection - to assure the product/material received meets the required specifications before it is manufactured. 2. In-process Inspection (On-going basis)- to assure the parts 3. Finished Goods Inspection (to ensure any secondary operations are performed to specifications and that product meets all requirements) This is the inspection side. Keeping all of this in mind, the concept of quality is to ensure the product is manufactured correct the first time.
What are the points you will keep in mind about the concept of quality control and inspection if you are the quality system manager of a rubber products manufacturing units?
Quality control and inspection are two distinctive functions of QSM (Quality System Manager). In the case of Rubber product, it may be a rubber band to the tire of an aeroplane , the quality is considered as most important.
What are the points about the concept of quality control and inspection of a rubber products manufacturing unit?
The application of the concept of Quality Control and Inspection for a rubber products manufacturing unit would consist of: 1.Receiving Inspection -- to assure the product/material received meets the required specifications before it is manufactured. 2. In-process Inspection (On-going basis)- to assure the parts 3. Finished Goods Inspection (to ensure any secondary operations are performed to specifications and that product meets all requirements) This is the inspection side. Keeping all of this in mind, the concept of quality is to ensure the product is manufactured correct the first time. If you have a more specific question you'd like answered and can provide more details on specific aspects of quality, I'd be happy to help. Feel free to add to your original question or contact us in the link below
What are the points you will keep in mind about the concept of quality control and inspection?
Since the inspetor gets paid badly .. Bribe money usely passes the inspetion..
What has the author Robert Ostertag written?
Robert Ostertag has written: 'Text-book of meat inspection (ante-mortem and post-mortem) including the veterinary control of meat and meat products' -- subject(s): Meat inspection 'Handbook of meat inspection' -- subject(s): Meat inspection
What does GMP stants for in manufacturing term?
GMP = "Good manufacturing practice".GMP is a set of practices and systems that have to be used in pharmaceutical industry (manufacturing, quality control, testing). These are general principles, not not prescriptive instructions.In United States GMP is enforced by the FDA.
In this sentence is quality control inspection an adjective?
For the phrase 'quality control inspection' the word quality is an adjective; the word control is a noun acting as an adjective; the word inspection is a noun.
What has the author Rudolf Kreuzer written?
Rudolf Kreuzer has written: 'Fish inspection and quality control' -- subject(s): Fish inspection, Food adulteration and inspection 'Shark utilization and marketing' -- subject(s): Fishery products, Shark fisheries 'Abraham Eilat'
What is inspection and what is quality?
difference between inspection and quality control?
When was the company Control Cable set up?
The company Control Cable was set up in the year 1975. Control Cable company are experts in design and manufacturing of cable products and much more.
What products does De Fanuc manufacture?
Upon cursory investigation into De Fanuc manufacturing, De Fanuc is a manufacturer of electrical supply products- more specifically in the robotics and control board arenas.
What is quality control management?
Quality control management is widely used in manufacturing companies. Quality control ensures that all products that a company makes and provides to consumers is in a good working standard before it leaves their possession.
