0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is meant by tinning stranded wires?
It is a reference for the preparation for soldering a stranded wire so you get a good joint. You twist the strands together, heat the wire with a soldering iron or gun and then apply a small amount of solder on the tip of the wire and it melts into the strands. Then you can solder the wire to another like wire or to a terminal or whatever. You basically reheat the wire to make connection and can add more solder as needed.Additional informationTinning is also useful if the wire is to be put in a "screw lug". The term "tinning" comes from the fact that older solder contains lead and tin. Some of the newer solder is supposed to be lead free.
Which is better galvanising or tinning?
galvanising :)
Can you use a two wire horn to replace a three wire?
probably yes.
How does tinning food kill bacteria?
Food is cooked to kill bacteria as it is canned; the cans then keep out any new bacteria.
How do you connect a 3 wire fixture to a 2 wire fixture that are connected to the same switch what do you connect the red wire to?
A three wire fixture most likely is one that has two separate loads within it. An example is a ceiling fan with a light fixture. If the three wire is used to separately switch the two loads you have to make a decision as to which load you want to work with the two wire fixture. Once that decision has been made connect the two wire fixture in parallel with the your selected load on the three wire fixture. On these types of installations the three wire fixture is usually controlled by two separate switches in a two gang box. The red and black wires of the three wire terminates on the bottom of either switch. The white wire is connected to the incoming neutral. The top of the switches are paralleled together with the "hot" feeder from the distribution source.
Why do you do tinning?
do tinning for wire to prevent rust do tinning for wire to prevent rust
Preparing the wire by coating it with solder is called?
Tinning
When you preparing a wire by coating it with solder what is it called?
It is known as tinning.
When was Bud Tinning born?
Bud Tinning was born in 1906.
Explain how to apply tinning technique in soldering?
Strip the wire to desired length. Then hold the wire horizontally and hold the soldering iron underneath the stripped part while holding the solder on the top of the wire. When the wire gets hot enough it will suck the solder into the wire
When was Iben Tinning born?
Iben Tinning was born on 1974-02-04.
When was Steen Tinning born?
Steen Tinning was born on 1962-10-07.
Two methods of active wire tapping are between lines transmission and?
piggyback entry
Why do you need to tin first the wire before soldering it?
pre tinning make it easier to solder wire because the solder is already " stuck" to the wire. and less solder will be needed to join the wire. if you watch the solder under a magnifier while tinning, you will notice the solder does not flow and "stick" until proper heat and flux ar applied. this heat usually is more than required to melt the solder because it takes mor heat to heat up the wire due to higher density. after tinning, less heat is required to melt the solder, and enough flux is usually left from tinning to quickly join the wire to the desired material provided the material is also tinned. this reduces cold solder and provides for a more relible connection. To tin the wire first is to cover the end of the wire with a layer of solder before you put it thru the hole in the PCB that will give you insurance of a proper electrical contact else you will put a heap of solder on the PCB without a proper contact with the wire itself what is called a dry joint that go for un tinted copper wire only normally all electronic component pins is factory tinted
How to What Is the Hot Dip Tinning Process Used by Brierley Coil Tinning, and How Does It Differ from Other Tinning Processes, Such As Electroplating or Chemical Tinning?
Brierley Coil Tinning specializes in the hot dip tinning process, which involves immersing a metal object, typically copper or copper alloy, in a bath of molten tin. The object is heated to a high temperature before being dipped in the tin bath, which creates a layer of tin on the surface of the object. Compared to other tinning processes, such as electroplating or chemical tinning, hot dip tinning offers several advantages. One of the main advantages is that it creates a thicker layer of tin, which provides greater corrosion resistance and durability. Hot dip tinning also creates a more uniform and consistent layer of tin, which can be important for certain applications. Another advantage of hot dip tinning is that it can be used to tin objects of various shapes and sizes, including large or complex objects that may be difficult to tin using other methods. This makes it a versatile and flexible process that can be used in a variety of industries, including electrical engineering, automotive manufacturing, and aerospace. Overall, the hot dip tinning process used by Brierley Coil Tinning is a reliable and effective way to provide a layer of tin on the surface of copper and copper alloy objects. With its ability to create a uniform, durable, and corrosion-resistant layer of tin, hot dip tinning is a valuable process that can help to extend the lifespan and performance of metal components.
What is meant by tinning stranded wires?
It is a reference for the preparation for soldering a stranded wire so you get a good joint. You twist the strands together, heat the wire with a soldering iron or gun and then apply a small amount of solder on the tip of the wire and it melts into the strands. Then you can solder the wire to another like wire or to a terminal or whatever. You basically reheat the wire to make connection and can add more solder as needed.Additional informationTinning is also useful if the wire is to be put in a "screw lug". The term "tinning" comes from the fact that older solder contains lead and tin. Some of the newer solder is supposed to be lead free.
When and where did baseball player Bud Tinning die?
Bud Tinning died January 17, 1961, in Evansville, IN, USA.
