0
- The BIOS, having completed its functions, loads the boot code in the master boot record and transfers control to it. The master boot record code begins execution. If the boot device is a floppy disk, the process continues with step 6.
- The master boot code examines the master partition table. It is searching for two things. First, it must determine if there is an extended DOS partition. Second, it must determine if there is a bootable partition specified in the partition table.
- If the master boot code finds an extended partition on the disk, it loads the extended partition table that describes the first logical volume in the extended partition. This extended partition table is examined to see if it points to another extended partition table. If it does, then that table contains information about the second logical volume in the extended partition, so it is loaded and examined. (Recall that logical volumes in the extended partition have their extended partition table chained one to the next.) This process is continued until all of the extended partitions have been loaded and recognized by the system.
- After loading the extended partition information (if any), the code attempts to boot the primary partition that is marked active (bootable). If there are no partitions marked active, then the boot process will terminate with an error. The error message is often the same one that occurs if the BIOS finds no boot device, and is generally something like "No boot device", but can be the infamous "NO ROM BASIC - SYSTEM HALTED".
- If there is a primary partition marked active, the code will boot it. The rest of the steps assume this is a DOS primary partition.
- The volume boot sector is loaded into memory and tested, and the boot code that it contains is given control of the remainder of the boot process.
- The volume boot code examines the structures on the disk that it is booting to ensure that everything is correct and in the right place. If not, the boot process will end in an error here as well.
- The code searches the root directory of the device being booted for the operating system files that contain the operating system. For a system running MS-DOS these are the files "IO.SYS", "MSDOS.SYS" and "COMMAND.COM".
- If the operating system files are not found, the boot program will display an error message, which is usually something like "Non-system disk or disk error - Replace and press any key when ready". Some people think that this message means the system was never booted, that the BIOS examined the floppy disk for example and just rejected it because it couldn't boot it. As you can see from this description of the boot process, the volume boot code was indeed loaded and executed, and in fact it is what prints the message when it can't find the operating system files! See here for an explanation of why this distinction is so important.
- If the operating system files are found, the boot program will load them into memory and transfer control to them. First, IO.SYS is loaded and its code executed. IO.SYS will then executed MSDOS.SYS (in pure DOS systems, MSDOS.SYS is just a text file in Windows 95 and later.) Then the more complete operating system code loads and initializes the rest of the operating system structures. For MS-DOS, this means loading the command interpreter (COMMAND.COM) and then reading and interpreting the contents of the CONFIG.SYS and AUTOEXEC.BAT system control files.
Wiki User
∙ 14y ago
Wiki User
∙ 11y ago1. Activate BIOS and setup programs
2. Initiate Power-On Self Test
3. Load Operating System
4. Configure the system
5. Load System Utilities
6. Authenticate the user
Add your answer:
Earn +20 pts
The purpose of a CPU?
A Central Processing Unit is the main processor in a computer that processes all the logic statements put to it. It is responsible for all the processing of the computer unless there is another process that does the job like a Graphics Processing Unit or Physics Processing Unit.
List the 4 steps in starting a computer?
The four steps to on a desktop computer isPlug in the plug and switch it onpress the button on the UPS if you have added onepress the button on the CPUallow it to start
What are the main functions of the main board?
The purpose of a computer board is to act as a main frame between all the computers working components. Without it, the computer would simply not run.
Main functions of computer?
The keyboard The main screen The hard drive The mouse If desktop it is the wire or cables If laptop it is the battery maintanance and Internet connectivity.
List the main types of computer viruses?
Trojan- A horse that infects the computer Worm- Makes computers stop Cakes- A type of infection that makes your computers stop from downloads Bug- Bugs that store and infect in your computer
What are the steps in boot processing?
It depends on what you have set-up for the computer to boot-up. A normal setting is for it to boot from the hardrive or if you are on Linux the setting normally is; BOOT-UP LINUX *-Disk Drive *-USB Ports(sometimes, but not normally) *-Hard Drive *-Floppy Disk
What is the main window when you boot up a computer?
The window when you boot up your computer is called the POST, Power On Self Test. It is bascially checking that all of your hardware is connected and has power.
What are the main steps in the night audit process?
The main steps when conducting the night audit process includes security checks. The processing of the late charges, processing floats and the balance of the shifts.
What are the main steps in the conduct night audit process?
The main steps when conducting the night audit process includes security checks. The processing of the late charges, processing floats and the balance of the shifts.
How the boot process works?
In computing, booting (also known as "booting up") is a bootstrapping process that starts operating systems when the user turns on a computer system. A boot sequence is the initial set of operations that the computer performs when power is switched on. The boot loader typically loads the main operating system for the computer,,,,,,,,,,,,,,,The computer word boot is short for "bootstrap" (itself short for "bootstrap load"). The term bootstrap derives from the idiom: to pull oneself up by one's bootstraps.[1] The term refers to the fact that a computer cannot run without first loading software but must be running before any software can be loaded, which seems as impossible as to "pull yourself up by your own bootstrapsRead more: booting
What is the main function i f the scientific process-?
The main function of scientific process is to help keep track of mistakes so it can be corrected. This is an experiment that is a process of steps.
What is the process of disputing a credit error?
Well the main thing is to contact your bank. None of the steps will be on the computer unless your bank says so. My suggestion is to call the bank ASAP and talk to them about it.
What are the three steps in the spreadsheet planning process?
your main point on what your going to say or do.
What are the different levels of a flow chart?
1)Basic flow chart-shows the main steps in a process for a good overview 2)process flow chart-gives details of a process by listing the main steps and sub-steps 3)developement flow chart- is similar to process flow chart but identifies persons or department involved in a process. 4)oppertunity flow chart- highlights decision making steps and inspection points.
Why is your computer unresponsive right after boot up?
The computer will normally become unresponsive because the computer is loading several files and services when displaying the main screen. Try uninstalling some unused programs or limit the programs that start on boot-up using msconfig.exe.
What are the function and duties of a computer microprocessor?
The main function of this part of the computer is to read scripts and process computer programs.
How do you prepare FIFO flow chart to adapt in automobile industry?
1)Basic flow chart-shows the main steps in a process for a good overview 2)process flow chart-gives details of a process by listing the main steps and sub-steps 3)developement flow chart- is similar to process flow chart but identifies persons or department involved in a process. 4)oppertunity flow chart- highlights decision making steps and inspection points.
