0
GE or Siemens cutler hammer universal CL series
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Does anyone make a 100 amp GFCI breaker?
Not that I know of. The largest GFCI breaker I have seen is a 60 amp.
Who makes a main breaker 200 amp service that has built in 200 amp gfci?
NOBODY!
Will a 2 pole 60 amp ITE Gould or Westinghouse breaker replace a 2 pole 60 amp T and B unit?
If the breaker will snap on the bus bar, yes.
I have a 15 amp tool hooked up to a 15 amp breaker- This trips the breaker even with nothing else running- There is also a GFCI outlet on the same circuit- Is the breaker or GFCI bad?
A 15 amp breaker will trip at 15 amps at an ambient temperature of 104 degree F. If the ambient temperature is higher the breaker will trip before 15 amps and if the ambient temperature is lower the breaker will trip after 15 amps. I would suspect the circuit is overloaded. But, you can change the breaker and see what happens. Just swap it with another one.
Do both the breakers and the outlets need to be GFI if you are running two 15 amp GFI circuits?
If you're using a GFCI breaker then the entire circuit will be protected by just the breaker alone. Every receptacle, switch, etc on that breaker will utilise the GFCI protection. You may have problems with it tripping if you plug in a motor (vacuum, etc) on the circuit.
Does anyone make a 100 amp GFCI breaker?
Not that I know of. The largest GFCI breaker I have seen is a 60 amp.
Who makes a main breaker 200 amp service that has built in 200 amp gfci?
NOBODY!
What size amp circuit breaker should be used for a pool light?
The pool light is usually on a 15 amp circuit. The breaker feeding this circuit must have a GFCI rating.
Will a 2 pole 60 amp ITE Gould or Westinghouse breaker replace a 2 pole 60 amp T and B unit?
If the breaker will snap on the bus bar, yes.
I have a 15 amp tool hooked up to a 15 amp breaker- This trips the breaker even with nothing else running- There is also a GFCI outlet on the same circuit- Is the breaker or GFCI bad?
A 15 amp breaker will trip at 15 amps at an ambient temperature of 104 degree F. If the ambient temperature is higher the breaker will trip before 15 amps and if the ambient temperature is lower the breaker will trip after 15 amps. I would suspect the circuit is overloaded. But, you can change the breaker and see what happens. Just swap it with another one.
What size circuit breaker for GFCI circuit in a normal size bath?
Normally it is a 20 amp using AWG 12/2 gauge wire. But it really depends on what size wire is on that circuit. If it is white AWG 14 gauge then use a 15 amp breaker. If it is yellow AWG 12 gauge then use a 20 amp breaker.
Do both the breakers and the outlets need to be GFI if you are running two 15 amp GFI circuits?
If you're using a GFCI breaker then the entire circuit will be protected by just the breaker alone. Every receptacle, switch, etc on that breaker will utilise the GFCI protection. You may have problems with it tripping if you plug in a motor (vacuum, etc) on the circuit.
Why are the GFCI breakers nuisance tripping in your 100 amp sub panel- is it because neutral bonded to ground?
It may be the GFCI breaker is defective. Make sure it is wired correctly. Neutral to neutral bar and ground to ground bar.
What is type of breaker for 41 amp's?
50 amp breaker.
Do they make a 30-40 amp two pole breaker compatible with a square d breaker?
No, if you have a Square D distribution panel only Square D breakers will fit in it.
How do you turn a 30 amp circuit into a 15 amp cicuit?
Replace the 30 Amp Breaker with a 15 Amp breaker.
Can you wire a 120 volt 7 amp Jacuzzi motor to a wall outlet in my bathroom?
No, it must be on a dedicated circuit of it's own. It must be on AWG 12/2 wire with 20 amp breaker. It also must be protected with a GFCI outlet.
