0
What can a dependent do if their EFMP packet is not being released to the EFMP coordinator so that they can get to the new command?
DrGenovese
Either utilize another MTF coordinator, contact your nearest Fleet and Family Support Center and ask for the EFMP Liaison for assistance or mail directly to the Central Screening Committe for your region.
Wiki User
∙ 12y ago
If a dependent's EFMP (Exceptional Family Member Program) packet is not being released to the EFMP coordinator, they can take the following steps:
- Contact their current command's EFMP coordinator directly to discuss the issue and request assistance.
- Ask for guidance from the ombudsman or family support office if available.
- Seek help from the EFMP office at their new command, informing them about the situation and asking for their support in obtaining the necessary paperwork.
Add your answer:
Earn +20 pts
What command is used to determine the location of delay for a packet traversing the Internet?
traceroute
Which command sends an echo request packet to an address and then waits for a reply?
ping
What is the function of the tracert command?
The tracert command is a command prompt command that's used to show several details about the path that a packet takes from the computer or device you're on to whatever destination you specify.
What is the function of tracert command?
The tracert command is a command prompt command that's used to show several details about the path that a packet takes from the computer or device you're on to whatever destination you specify.
What is the function of command tracert?
The tracert command is a command prompt command that's used to show several details about the path that a packet takes from the computer or device you're on to whatever destination you specify.
What command you use to deinstall a rpm packet foobar from your system?
yum remove foobar
What packet is used in ping command?
Packet Internet Groper(PING) is an Internet Control Message Protocol(ICMP) request packet for it's working. ICMP packets are used to check networks are live or not. -- By MYNarutoAnime ----
What steps are taken when forwadin an icmp packet?
For each router, the following steps occur: 1) The "access-group in" command is checked on the interface, and discards the packet if the rule tells it to do so. 2) The "TTL" field is decreased by 1. 3) If TTL is now 0, the router discards the packet and sends a reply packet back to the sender. 4) The packet's IP address is compared to the routing table to determine the next hop of the packet. 5) The router advises if the network or host is unreachable due to a down interface or no known route. 6) The router sends the packet to the outgoing interface's queue to be sent to the next hop. 7) The "access-group out" command is checked on the interface, and discards the packet if the rule tells it to do so. 8) The router sends the packet to the next hop.
Write difference in the form of a table between Ping and Trace Route command?
The Ping command sends a small packet of data to a destination IP address and waits for a response. It measures the time it takes for a packet to travel from the source to the destination. This command is typically used to check if a network device is online and responding to requests. On the other hand, the Trace Route command sends a series of packets to a destination IP address and tracks the route that each packet takes. It identifies each router or hop that a packet goes through on its way to the destination. This command can be used to diagnose network latency issues or identify where data is being lost. While the Ping command only provides information on the time it takes for a packet to reach the destination, the Trace Route command provides more detailed information on the network path and any delays or losses that occur along the way. In summary, both the Ping and Trace Route commands can be useful in troubleshooting network issues, but they serve different purposes. The Ping command is a simple tool for testing connectivity to a destination device, while the Trace Route command provides more detailed information on the network path and any issues that may be occurring.
When a router receives a packet with destination address that is within an unknown subnetwork of a directly attached network what is the default behavior if the ip classless command is not enabled?
broadcast the packet through all interfaces except the one on which it was received
Which command do you use to verify the operation of the NAT feature by displaying information about every packet that is translated by the router?
debug ip nat
15 How do you know the path that a packet takes to the destination?
You use the traceroute command. Example, in Windows: open a command window, and type tracert wiki.answers.com.You use the traceroute command. Example, in Windows: open a command window, and type tracert wiki.answers.com.You use the traceroute command. Example, in Windows: open a command window, and type tracert wiki.answers.com.You use the traceroute command. Example, in Windows: open a command window, and type tracert wiki.answers.com.
