I dont think Pepper is particularly dissolvable in water so I'd dissolve the mixture in some warm water, then filter off the pepper granules, leaving the solution of salt which you can evaporate to give you the salt.
A magnet as the sand is nonmagnetic. You could also use water as mixing the two sand will dissolve at a high enough temperature and enough stirring whereas the fillings will sink to the bottom.
I would use a magnet to remove the iron filings, then toss the remainder into the air in a slight breeze to remove the pepper as with a basket to separate wheat from chaff, then dissolve the salt with water, leaving only sand.
magnet because the iron will stick except for the black pepper.
A magnet should work very nicely to pick up the iron filings, but leave behind the sand.
Iron can be separated with a magnet.
First, place the sulfur, sand and iron filings in a plastic container. Next, use a magnet to remove the iron filings from the sulfur-sand mixture and surely,the iron filings will connect to the magnet, leaving the sulfur and sand behind.
Here's the full scientific report I had to do in year 7. Title: Magnetic Separation Aim: To separate iron filings from sand using a magnet. Equipment: Magnet, sand and iron filing mixture, plastic bowl Method: 1. Pour the mixture into the plastic bowl 2. Move the magnet slowly through the mixture Results: When the magnet was moved through the mixture, it picked up the iron filings but not the sand. Conclusion: In this experiment we demonstrated that a magnet can pick up iron filings in a sand and iron filing mixture through magnetism. The aim was achieved as we were able to separate the iron filings from the sand.
In solution, the salt will be dissolved in the water, the sand and iron will settle to the bottom of the container. Separate out the water, evaporate the water and the salt will remain, separate the sand and iron filings with a magnet.
A heterogeneous mixture: There are no chemical bonds between the iron filings and sand.
What is special about iron filings? Anything with iron in it has this property... magnets are attracted to iron! Magnets do not attract sand. You can use a magnet to separate iron filings from sand.
Hover a magnet over the mixture.The iron filings will be attracted to it.A mixture of sand and camphor will be left. Then,separate the mixture of sand and camphor by using sublimation.
This can be done by the processs of magnetism. Holding amagent near the mixture will cause the iron filings to be attracted out of the sand.
First, place the sulfur, sand and iron filings in a plastic container. Next, use a magnet to remove the iron filings from the sulfur-sand mixture and surely,the iron filings will connect to the magnet, leaving the sulfur and sand behind.
water and a magnet
In solution, the salt will be dissolved in the water, the sand and iron will settle to the bottom of the container. Separate out the water, evaporate the water and the salt will remain, separate the sand and iron filings with a magnet.
Here's the full scientific report I had to do in year 7. Title: Magnetic Separation Aim: To separate iron filings from sand using a magnet. Equipment: Magnet, sand and iron filing mixture, plastic bowl Method: 1. Pour the mixture into the plastic bowl 2. Move the magnet slowly through the mixture Results: When the magnet was moved through the mixture, it picked up the iron filings but not the sand. Conclusion: In this experiment we demonstrated that a magnet can pick up iron filings in a sand and iron filing mixture through magnetism. The aim was achieved as we were able to separate the iron filings from the sand.
In solution, the salt will be dissolved in the water, the sand and iron will settle to the bottom of the container. Separate out the water, evaporate the water and the salt will remain, separate the sand and iron filings with a magnet.
It is a mixture
You can move a magnet back and forth right above the mixture. The iron filings will get attracted to the magnet and stick to it while the sand will remain in the container. Iron is a magnetic material while sand is not.
By using a magnet to separate the iron filings, you'd be left with the sulfur and sand mix. Selecting a solvent for the sulfur will allow you to dissolve the sulfur, and then all you have to do is put the sand in a filter and wash the sulfur through with the solvent.
Use a magnet to remove all the iron filings, then using a cloth bag, add water to the sand and salt. The salt will dissolve in the water, leaving the sand in the cloth bag.
the correct answer would be -( magnetic attraction of one part )