0
What can you do if you hooked the white black and copper wires to the appropriate wires of a light fixture having 2 switches - there is also a red wire - but light will not turn off on either switch?
Wiki User
∙ 14y ago
If this is a standard light controlled by two switches you will need to use the red wire too. For more information and a wiring diagram see the answer to the Related Question shown below.
<><><> Maybe you need to use the red wire not the black? In situations where you have black and red wire in light boxes, the black is often used as an "always hot" wire coming from the breaker panel and the red is then used as the "switched hot" wire. But do not assume anything when working with household electricity: you must always check with a properly insulated voltmeter or some other type of safely insulated voltage indicating device. <><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you connect a 3 wire fixture to a 2 wire fixture that are connected to the same switch what do you connect the red wire to?
A three wire fixture most likely is one that has two separate loads within it. An example is a ceiling fan with a light fixture. If the three wire is used to separately switch the two loads you have to make a decision as to which load you want to work with the two wire fixture. Once that decision has been made connect the two wire fixture in parallel with the your selected load on the three wire fixture. On these types of installations the three wire fixture is usually controlled by two separate switches in a two gang box. The red and black wires of the three wire terminates on the bottom of either switch. The white wire is connected to the incoming neutral. The top of the switches are paralleled together with the "hot" feeder from the distribution source.
Can you connect one single light switch to another single light switch to control the same light on or off.?
Yes you can. There are three ways of doing this. Two are incorrect and one is the correct way of doing it.The two switches can be paralleled together to make the light fixture respond. Both of the two switches will always have to be in the on position. Either switch will turn the light off but the second switch will not turn the light on. Very inconvenient when you enter a room through one door and leave by another.The two switches can be wired in series. Both switches have to be on to operate the light but again if one of either switch is left in the off position the other switch will not operate the light fixture. Very inconvenient when you enter a room through one door and leave by another.The correct way of wiring two switches to control a central light fixture is with a three way switching system (two way in the UK). The two positions have to have special three way switches in each position. These types of switches sort out the problems of leaving a switch in a certain position to operate properly. The only criteria is that there be a three conductor cable joining the two three way switch boxes together.See related links below.
What will happen if the two switches connected to light up a single bulb are on?
It is dependant on whether the switches are in wired in a parallel or series configuration. If the switches are wires in parallel then both switches would have to be off to turn the light bulb off. Either switch could turn the light bulb on. If the switches are wired in series then both switches would have to be on to turn the light bulb on. Either switch could turn the light bulb off.
Why would a fixture burn through 2 bulbs in 2 months?
Either you are unlucky or you buying cheap bulbs.
You are changing a light fixture but the wires are all the same color which one is the hot wire?
A light fixture will function normally either way. The hot and neutral wires are interchangeable. DANGER! This is only true of lighting fixtures!
How do you connect a 3 wire fixture to a 2 wire fixture that are connected to the same switch what do you connect the red wire to?
A three wire fixture most likely is one that has two separate loads within it. An example is a ceiling fan with a light fixture. If the three wire is used to separately switch the two loads you have to make a decision as to which load you want to work with the two wire fixture. Once that decision has been made connect the two wire fixture in parallel with the your selected load on the three wire fixture. On these types of installations the three wire fixture is usually controlled by two separate switches in a two gang box. The red and black wires of the three wire terminates on the bottom of either switch. The white wire is connected to the incoming neutral. The top of the switches are paralleled together with the "hot" feeder from the distribution source.
What is used to support vertical copper tubing against wood blocking?
The popular and proper mounting technique for copper tubing is a copper tubing clamp for the appropriate size. This clamp is made of copper and should be mounted with copper nails. It resembles a piece of tubing of the appropriate size, a half inch wide with two ears on either side with holes for nailing.
How did they use to wire two on off switches to one fixture?
You need two 3-way switches. To see a diagram use your favorite search engine and search for 3-way switch wiring. Each switch has a common connection point and two other terminals. Basically connect the "other" terminal on 1 switch to either "other" terminal on the second switch and then do it again for the remaining "other" terminal. Then connect the common on one switch to the fixture and the common on the remaining switch to supply voltage. Tie neutral and ground for fixture and supply to the white and bare wires respectively.
Can you connect one single light switch to another single light switch to control the same light on or off.?
Yes you can. There are three ways of doing this. Two are incorrect and one is the correct way of doing it.The two switches can be paralleled together to make the light fixture respond. Both of the two switches will always have to be in the on position. Either switch will turn the light off but the second switch will not turn the light on. Very inconvenient when you enter a room through one door and leave by another.The two switches can be wired in series. Both switches have to be on to operate the light but again if one of either switch is left in the off position the other switch will not operate the light fixture. Very inconvenient when you enter a room through one door and leave by another.The correct way of wiring two switches to control a central light fixture is with a three way switching system (two way in the UK). The two positions have to have special three way switches in each position. These types of switches sort out the problems of leaving a switch in a certain position to operate properly. The only criteria is that there be a three conductor cable joining the two three way switch boxes together.See related links below.
How do you add a light to a double switch?
The switch you are referring to is called a three way switch operating one or a string of devices from two separate locations. You have to either parallel it at the existing light or find out which end the switch leg and associated neutral is on. Sometimes the electrician will feed the fixture with the neutral and use travellers between switches with 3 wire circuits so you first need to know how it has been wired. It is legal to feed the switches and lamps from any of the locations. Unless you are tapping into the light fixture itself, I would have a professional look at it.
What is the chandelier on Poptropica?
its the light fixture close to where the princess is. There is one on either side
What will happen if the two switches connected to light up a single bulb are on?
It is dependant on whether the switches are in wired in a parallel or series configuration. If the switches are wires in parallel then both switches would have to be off to turn the light bulb off. Either switch could turn the light bulb on. If the switches are wired in series then both switches would have to be on to turn the light bulb on. Either switch could turn the light bulb off.
Where do you get copper?
Either from the copper mines Or the Brazilian copper tree plant which are on the decline because of acidic rain
When do they announce the Spanish fixture list?
5 - 7 days before the fixture diue to Spanish TV rights. It can be moved to either the Saturday or be scheduled for two separate times on the Sunday evening.
What is the effect of copper on tantalum nitride?
There will either be no reaction or the copper would replace the tantalum...
How do you calculate toilet fixtures?
Drainage fixture units are used for calculating either public or private toilets.
The only fixture that will appear on planogram is?
its either: Cosmetic fixtures, Gondolas, Greeting card fixtures... or all of them
