0
What else can I help you with?
Why a rod immersed partially in a transparent liquid appears to be bent at the surface of the liquid?
When light travels from one medium to another (e.g. from air to a liquid), it changes speed and direction. This causes the light rays to bend or refract at the interface between the two mediums. This change in direction can make the rod appear bent at the surface of the liquid when viewed from outside.
If 60 lbs of force must be applied to the valve for it to open how much upward force must push rod X apply for the valve to open?
The upward force required on push rod X to open the valve would also be 60 lbs, as it must be equal to the force needed to open the valve. Push rod X needs to counteract the same amount of force applied on the valve for it to open.
What happens when you rub a lucite rod with fur?
Rubbing a lucite rod with fur causes the rod to become charged by friction. Electrons are transferred from the fur to the lucite rod, giving the rod a negative charge and the fur a positive charge. This is known as triboelectric charging.
How a glass rod charged when rubbed with wool?
When a glass rod is rubbed with wool, electrons are transferred from the wool to the glass rod, making the rod negatively charged. This transfer of electrons causes the glass rod to become statically charged, meaning it has an excess of negative charge.
How would you hit a metal rod to make a transverse wave?
You can hit a metal rod with a mallet or hammer to create a disturbance that propagates through the rod as a transverse wave. The force of the impact causes particles in the rod to move perpendicular to the direction of the wave's propagation, creating crests and troughs along the rod.
What causes a bad push rod in a 84 Chevy 350 engine?
It is probably a broken valve spring.
What causes a tie rod to bend?
There are many causes for a tie rod on a vehicle to bend. This can occur due to hitting a pothole while driving or a curb.
Can loose rocker cause bent push rod?
Sure can, Quick A bent push rod will cause a loose rocker A loose rocker has no way to bend a push rod, there is no pressure.
What are the causes of a sudden massive oil leak?
A broken sump, possibly due to a broken Con-Rod.
What causes a rod to get bent?
It could be some sort of liquid in the cylinder. It will cause it to hydraulic and bend rods.
Will normal driving cause a tie rod to bend?
No, normal driving will not bend a tie rod. It takes a large shock from a large pot hole, a curb or a collision to bend a tie rod.
How do you open the hood on a 1985 Corvette?
you have to trip the upper latch clip do do this you need a l bend rod to push under the hood and push the clip to rhe out side edge of the fender to pop the latch
Can broken terminals causes misfire?
The normal causes for a misfire would be Faulty: spark plug, spark plug wire, ignition coil, ignition module, fuel injector are the most common. Coolant leaking into a cylinder is another. Internal engine problems such as burnt valve, broken valve spring, bent push rod, worn rings
What can cause bent push rod?
A bent push rod can be caused by several factors, including excessive engine wear, improper installation, or incorrect valve timing. Over-revving the engine can also lead to a push rod bending due to increased stress on the components. Additionally, issues such as a broken valve spring or a stuck valve can create abnormal forces that result in a bent push rod. Regular maintenance and inspection can help prevent these issues.
Can a backfire cause a bent push rod?
Yes, a backfire can cause a bent push rod. When an engine backfires, it creates a sudden and violent explosion in the intake or exhaust system, which can generate excessive pressure. This pressure can lead to a rapid movement of engine components, potentially causing the push rods to bend if they are subjected to forces beyond their design limits. Additionally, other factors like misadjusted valves or improper timing can exacerbate the risk of bending a push rod during a backfire.
How are the exhaust and intake valves arranged in the 3400 V6 Aztek?
intake short push rod, exhaust long push rod. put short push rod on rocker closes to intake manifold.
Is the intake push rod longer than the exhaust push rod in a gm 3.1?
exhaust puh rod is longer. they measure 6 inches while intake push rods measure 5.68 in
