0
It is usually classed as a device that will open the circuit if the current in the circuit goes high. Two examples of these types of devices are fuses and circuit breakers.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is the two forms of circuit protector?
Fuse and circuit breaker
What is the rating circuit of the 3 phase appliance protector?
16A
What should they buy to protect their computer during future lightning storms power surge circuit board ground wiresurge protector?
A surge protector
How are appliances protected from power surges in three-pin plugs?
With a surge protector. The surge protector opens the circuit if a surge is detected. The third "pin" is connected to a ground wire to protect the circuit from a short and to dissipate "stray" charges. Overload breakers protect users and equipment from overloads , usually caused by shorts, by heating up and opening the circuit.(same as a surge protector.)
What are the dangers of pigtail surge protector?
Answer for USA, Canada and countries running a 60 Hz supply service.There are no dangers to using a pigtail surge protector. The installation of the protector must be done correctly though. The pigtails must not be installed on an existing circuit that has an existing load on it unless the breaker is approved for more than one circuit load on it. The protector must use a new two pole breaker with no additional load on it except the surge protector. This is the correct procedure to connect a pigtail surge protector to a distribution panel board.
What types of overload protection for circuits in a single family dwelling?
Fuses, Circuit Breakers, GFCI (Ground Fault Circuit Interrupter), Surge Protector, etc.
Is tv parallel or series circuit?
The outlets in your house are in parallel with each other. If your question is is your TV in series with something else plugged into your house, it is not, it is in parallel (since your house wiring is in parallel). The giveaway for series or parallel circuits is if you remove one element in a series circuit, you will kill all other elements. In a parallel circuit, there shouldn't be a noticeable difference. For example, if you have a surge protector plugged into your wall, and a lamp plugged into your wall, and your TV and DVD player are plugged into the surge protector: The surge protector is in SERIES with your TV and DVD player The surge protector is in PARALLEL with your lamp The DVD player and TV are in PARALLEL
What is the function of the overload protector?
The bimetallic overload protector is mounted in series with the motor windings. Should the current in the motor windings increase to a dangerous value, the heat developed by the passage of the current through the protector will cause it to open. This breaks the circuit to the motor windings and stops the motor before any damage can occur.
What is the function of overload protector in refrigerator?
The bimetallic overload protector is mounted in series with the motor windings. Should the current in the motor windings increase to a dangerous value, the heat developed by the passage of the current through the protector will cause it to open. This breaks the circuit to the motor windings and stops the motor before any damage can occur.
What happens when you press the reset button on a surge protector by accident and then it doesn't work anymore?
The reset button only resets the built in circuit breaker in the power strip section of the surge protector. If it quit working then you may have pressed it too hard and broken the circuit breaker's mechanism (this is hard to do but possible) and the device is now scrap. Replace it with a new surge protector.Pressing reset by accident is really very unlikely to break the circuit breaker's mechanism, but I didn't see what you did.
Is it safe to put a surge protector into a wooden box in order to hide all the cords on the counter?
I see no reason not to. As long as the surge protector is in good condition and the plugs that are connected to it have a snug fit. Most surge protectors have there own built in protection and if the whole unit is just plugged into the wall outlet the circuit breaker will trip if the surge protector faults.
Where is the reset button on the belkin surge protector BG108000ce2M?
The reset is part of the resettable circuit breaker. It is located just below the "not grounded" light that indicates when a ground is not present
