Want this question answered?
You put switch in series with the black supply wire and the black wire to the first light. Then connect black wire of first light to black wire of second light, black wire of second light to third light and so forth. Do the same with the white wires and ground wires.
with a standard 1 pole light switch (one switch operating the light) it is black wire to black wire and white to white (non grounded)
You have a 3 way switch. Your black wire is the hot wire. Your green wire is the ground wire. Your red and white wires go to the light and other switch. You should have gotten a wiring diagram with your switch.
You would wire the switch to the first light. Code says to break the black or power side of the circuit. Connect the white to the light. Take the black down to the switch on the black wire and back to the light on the white. This is a line of wire from the light to the switch. From the first light, take the white and the return white from the switch to the second with another run of wire. This will be regular black white with ground. White to white and at the first light the return line from the switch is white but hook to the black to the second light. Second light to third just continues the two wires. Black to black, white to white. I think this is clear enough to follow. If not, ask again.
If the question is, can I wire a switch to an existing light fixture (and I must assume that it's something like a pull-chain light fixture), the answer is yes.If the question is, "how do I wire a switch to an existing light fixture that has no external switch", the answer is, "in series".The attached web site gives simple instructions on how to wire a basic light switch to an existing light.See sources and related links below
You put switch in series with the black supply wire and the black wire to the first light. Then connect black wire of first light to black wire of second light, black wire of second light to third light and so forth. Do the same with the white wires and ground wires.
with a standard 1 pole light switch (one switch operating the light) it is black wire to black wire and white to white (non grounded)
Current flows through a wire when a light switch is turned on.
You have a 3 way switch. Your black wire is the hot wire. Your green wire is the ground wire. Your red and white wires go to the light and other switch. You should have gotten a wiring diagram with your switch.
You would wire the switch to the first light. Code says to break the black or power side of the circuit. Connect the white to the light. Take the black down to the switch on the black wire and back to the light on the white. This is a line of wire from the light to the switch. From the first light, take the white and the return white from the switch to the second with another run of wire. This will be regular black white with ground. White to white and at the first light the return line from the switch is white but hook to the black to the second light. Second light to third just continues the two wires. Black to black, white to white. I think this is clear enough to follow. If not, ask again.
you have to pull the feed wire off the brake switch to supply power to the new third brake light. get a test light and test the wires on the brake switch....one is hot all the time the other one gets hot when you depress the pedal....that is the one you need. do not take it pull your power from the rear light it might have an intergrated turn signal wire. which would make your 3rd brake light blink.. ok.have fun! you have to pull the feed wire off the brake switch to supply power to the new third brake light. get a test light and test the wires on the brake switch....one is hot all the time the other one gets hot when you depress the pedal....that is the one you need. do not take it pull your power from the rear light it might have an intergrated turn signal wire. which would make your 3rd brake light blink.. ok.have fun!
You have to test the multifunction switch and make sure the wire harness is good. It most likely the multifunction switch.
If you have one wire into your switch box for your light. this is called a switch leg, the dimmer should be wired across the black and white wire wires.
by a parellal current switch.
The switch probably turns the light out when the switch makes connection, then the light is on when there is no connection (like when the wire is not connected.) Reconnect the wire and push the switch to see if the light goes out. The switch is most likely out of adjustment or bad.
changing the wires to the on-off switch.
How do I connect a wall light switch that has 3 terminals, the third being for the ground wire. Which terminal should be connected to power coming from the breaker box?