0
What electrical safety procedure is described below If you are going to work on something electrical you should first disconnect it completely from its electrical source Then you have to make sure tha?
Wiki User
∙ 10y ago
Lock Out, Tag Out
This is the process of disconnecting the power supply, locking it so no one can turn it back on and tagging the lock so people know why it is locked out and who locked it. It is against the law in some states and OSHA for someone else to unlock it.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What are safe work procedure for working in the rain with electrical equipment?
See discussion page for further information.
You want to transfer your Electricity bill from your builder to your name?
The usual procedure is for the electrical contractor to take out a permit for his work which can include a temporary service pole for his electrical use. When his work is finished, the home owner takes out a connection permit from the utility company to have the new service connected. The electrical inspector checks the contractors work and signs off on the job and send a receipt to the utility company saying that the job is safe to connect. It is the home owners responsibility to pay all the fees for the connection. When the utility company comes out to connect, usually they will disconnect the electrical contractors temporary service and swing the feed over to the house for a permanent connection.
What is the definition of trans-stimulation?
Trans-stimulation is a procedure used to depolarize the neurons in the brain. Electromagnetic is used to weaken the electrical currents that are currently running through the human brain.
What best practice to avoid electrical shock?
Never place items, especially metal utensils, inside an electric appliance while it is plugged into a wall outlet.Children tend to stick paper clips or other small items they find in electrical outlets.Never forget -- water and electricity don't mix.Inspect wiring of equipment before each use. Replace damaged or frayed electrical cords immediately.Know the location and how to operate shut-off switches and/or circuit breaker panels. Use these devices to shut off equipment in the event of a fire or electrocution.Use safe work practices every time electrical equipment is used.Use only multi-plug adapters equipped with circuit breakers or fuses.
What procedure is used to separate and analyze DNA fragments by placing a mixture of DNA fragments at one end of a porous gel and supplying an electrical voltage to the gel?
agarose gel electrophoresis
What electrical safety procedure is described below if you are going to work on something electrical you should first disconnect it completely from its electrical source then you have to make sure?
Lock Out, Tag Out This is the process of disconnecting the power supply, locking it so no one can turn it back on and tagging the lock so people know why it is locked out and who locked it. It is against the law in some states and OSHA for someone else to unlock it.
How do you replace altrnator in Lincoln mark 8?
Disconnect the battery, remove the serpentine belt and remove the bolts, disconnect the electrical connection and remove. Reverse the procedure to install.
How do you replace the passenger side mirror on a 2005 Ford Focus?
Removal and Installation Remove the trim panel. Release the clip. Release the locating tabs. Remove the trim panel. Disconnect the exterior mirror control switch electrical connector. Disconnect the exterior mirror electrical connector. Release the clip. Release the electrical connector. Disconnect the electrical connector. Remove the exterior mirror. Remove the bolt. If equipped, remove the screw. To install, reverse the removal procedure.
How do you remove fuel tank 93 Thunderbird?
First remove gas cap, then disconnect exhaust from flange by fuel tank. Disconnect fuel pump electrical connection, disconnect fuel filler hose and evap line from top of tank. Disconnect quick connect fittings on top of tank. Lower tank. This procedure should be done with the tank less then 1/4 full.
How does you replace the blower motor switch on a 2003 mercury stable?
Disconnect the negative battery cable.Using the Radio Removing Tool 415-001, pull out the integrated control panel.Label and disconnect the electrical connectors. If equipped with Electronic Automatic Temperature Control (EATC), disconnect the in-car temperature sensor hose.Remove the integrated control panel.To install, reverse the removal procedure.
What procedure abnormal electrical pathways in the heart?
no
How do you change a Blower Motor on a 1990 Buick Century?
Disconnect battery ground cable. Disconnect blower motor electrical connections. Remove blower motor attaching screws, then blower motor. On models with A/C it may be necessary to dismount alternator and move away from module. Reverse procedure to install.
What procedure destroys abnormal electrical pathways in the heart?
no
How do you change ford 500 PCV valve?
Disconnect the PCV valve tube from the PCV valve.Disconnect the PCV valve electrical connector if it has one.Turn the PCV valve counterclockwise to remove from the valve cover.To install, reverse the removal procedure.
How do you replace an exterior driver's side door handle on a 1998 Lincoln Mark VIII?
Disconnect positive battery cable, remove all the bolts and screws from the door panel, disconnect the electrical plugs and carefully remove the panel. Remove the two nuts that hold the handle on, remove the linkage and reverse procedure to install.
How is a standard operating procedure described in clinical research and practice?
A standard operating procedure is described with the correct terminology and format in clinical research and practice. Such formatting and word choice helps prevent confusion and makes the procedure concise and easy to follow.
How do you find the electrical test procedure for electric heaters?
AT TARGET
