0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What are the various phases of an instruction cycle Give the micro operation of fetch and decode phases?
there are 4 phases in instruction cyclefetchdecodeexecutestore
What does 'cross phase' mean for a 3-phase electrical supply?
The following is pretty colorful but in reality you will see nothing as the safety equipment stipulated by the electrical code trips the circuit open before any serious damage is done. On a circuit that has tripped on a ground or phase fault the first thing to be done is isolate the circuit using lock out procedure. The trouble shooting equipment used is a megger. Once the fault is located and repaired, the circuit is re fused or the breaker reset, power turned on and an amperage reading is taken. If all the equipment is within the manufactures specifications the circuit is signed of as operational. To quote Billy Mays "KABOOM!". For any two or more phases to make mechanical contact in a three phase electrical system creates the ultimate dead short. This results in an immediate explosion with an arc flash brighter than the surface of the sun and a complete meltdown of the conductors and equipment. Simply put, you don't want to cross phases or allow them to make contact in any single or three phase system. This is the worst thing any electrician can do.
How to parallel the Dyn1 and Dyn11 Transformer?
you keep the hv & lv on the dyn11 tx straight in phasing. you then put a cross on any two phases on the hv side of the dyn1 tx, and do the same cross with the phases on the lv side of the tx. for instance lets say we cross a & c phases on the hv & lv sides of the dyn1 tx. now draw a diagram with the four tx, split them up, 2 x dyn1, 2 x dyn11. now on the diagram where you have dyn1 tx, change the the phase plates to read cba left to right, also change the lv side to match. leave the phase plates on the dyn11 tx alone to read abc left to right on both sides. now draw the cables going between them on the hv & lv sides. now if a phase always goes to a phase and b & c phases do the same it will all tie in. prove it to yourself and follow a phase threw all the tx's, do the same will b & c phases. I do it all the time at my job, works every time.
What are the three important phases in the manufacturing process?
3 phases in manufacturing process
What is the value of resistivity?
Electrical resistance is measure in Ohms. A function of voltage divided by current. It is also dependant on the length and cross sectional area of the conductor.
What happens as the moon revolves around the earth?
we get different phases of the moon
What do you mean by electrical double wrapped cross joint?
An electrical double wrapped cross joint is just like an ordinary cross joint but double wrapped with electrical tape. It is used where two tap conductors need to extend away from the branch conductor in the opposite direction and is stronger than the ordinary cross joint.
Is a cross connection when plumbing and electrical systems mix?
NO.
Why use a phase barrier in electrical ciircuits?
Phase barriers enhances the distance between two phases thus making the medium between two phases less vulnerable for breakdown.
What happens during each of the four phases of the menstrual cycle?
u bleed
What happens if you break a cross?
Nothing will happen if you break a cross.
What happens to the cross products when the terms of a proportion are cross multiplied?
The cross product is created.
What brands of breakers cross reference with GE thqb series breakers?
Siemen's is a brand of electrical breakers that will cross reference with GE thqb series breakers. Electrical breakers can be replaced by other brands if they are of the same type and fit in an electrical box.
What happens when you break a cross?
NOTHING
What happens if you did not have the red cross?
then you are dead.
What is a rotary phase converter commonly used for?
A rotary phase converter is commonly used to convert a single phase electrical power source to three phases. This allows you to use three phases instead of one.
What happens twice a month at full and new moon phases?
i go beserk and turn into a werewolf
