0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
If there is a break at any point in a series circuit the current will?
not flow
Why parallel combination is preferred over series combination?
In a parallel circuit (with more than one branch), the current will still flow in the other circuit(s) even if there is a break in one circuit. This is not so with a series circuit, since it does not have branches: if there is a break in the circuit, there is a break in the circuit.
When there is a break on the circuit what is the reading?
The typical answer is current is zero when there is a break in the circuit. It depends on the complexity of the circuit, there may be other paths for the current to flow, such that if there is a break in one part of the circuit, the rest of the circuit still has current flow (but a different value than designed). If you are reading voltage, and there is a break then that will change, also depending on the complexity. If it is a single loop, and you're reading voltage before the break, your voltmeter will read the same voltage as the voltage source, since there is no current flowing between any resistors between the meter and the source. If you're reading voltage after the break then the meter will read zero (0) volts.
What are the differences between Break Continue and Exit?
break - The break statement is used to jump out of loop. After the break statement control passes to the immediate statement after the loop.continue - Using continue we can go to the next iteration in loop.exit - it is used to exit the execution of program.note: break and continue are statements, exit is function.
What is Disconnector Switch?
to disconnect the circuit when faults occursAnswerA 'disconnector switch' is another term for an 'isolating switch' or 'isolator'. It is a manually-operated switch used to provide a visible break between a de-energised part of a circuit and the energised part of a circuit so that work can be carried out safely on the de-energised part. A disconnector switch is not intended to break a load current, and most certainly not designed to break a fault current -that is the function of a circuit breaker.
A break in the wires of an electric current will the circuit and the current?
A break in the wires of an electric current will break or cut the circuit and stop the current from flowing.
What does a guy usually do when he wants to break up with his current gf for you Does he ask you if you like him if so what should you say?
tell him the truth...
Can a wooden oar be broken?
Yes . I've witnessed it, but it did not break from water current so wooden oars are safe to paddle with
What happens to an ammeter when there is a break in a circuit?
An ammeter reads the current that is flowing through a branch of a circuit. If there is a break within that same branch of the circuit, current will not be able to flow through that branch of the circuit as it forms an incomplete loop, so the ammeter will read 0 A of current. If there is a break in a circuit in a branch that is not connected to the ammeter however, the ammeter will give a higher reading of the current. This is assuming that the break in the other branch does not short out the branch with the ammeter attached, and that the circuit can still form a complete loop without that branch.
Did Asking Alexandria break up?
No, they have not at this current time.
What will an ammeter show if the circuit is broken?
Zero. No current is flowing in an open circuit. The ammeter will display an amount of 0 amps because there is no longer any current once the circuit has been broken. An ammeter measures current.
What does a circuit breaker do in scientific terms?
It does what is says, breaks the circuit. The actual term for this is creating an Open. Current can only flow through a complete circuit, so if there is an open(break) in the circuit, current will not continue to run.
If there is a break at any point in a series circuit the current will?
not flow
Define fusing current?
The fusing current of a wire is the current that will cause the wire to overheat and melt, which will break the circuit, acting like a fuse.
Why parallel combination is preferred over series combination?
In a parallel circuit (with more than one branch), the current will still flow in the other circuit(s) even if there is a break in one circuit. This is not so with a series circuit, since it does not have branches: if there is a break in the circuit, there is a break in the circuit.
When there is a break on the circuit what is the reading?
The typical answer is current is zero when there is a break in the circuit. It depends on the complexity of the circuit, there may be other paths for the current to flow, such that if there is a break in one part of the circuit, the rest of the circuit still has current flow (but a different value than designed). If you are reading voltage, and there is a break then that will change, also depending on the complexity. If it is a single loop, and you're reading voltage before the break, your voltmeter will read the same voltage as the voltage source, since there is no current flowing between any resistors between the meter and the source. If you're reading voltage after the break then the meter will read zero (0) volts.
How are fuses and switches similar?
A fuse can break the current flowing in a circuit only once whilst a switch can break the current flowing in a circuit many times. In other words a switch can switch the current on and off - and then on again and off again - indefinitely but a fuse can only switch off the current once.
