0
What heating element would you switch on to heat the whole tank?
Wiki User
∙ 13y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What are the four features required to construct a working simple circuit?
power source, wire, switch, end fixture. Simplest circuit would be a power source and a heating element. No wire or switch needed.
What element is in the heating element for toasters?
That would most likely be a nickel and chrome alloy. Light bulbs use tungsten.
What would cause the average atomic mass to be close to a whole number?
The average atomic mass of an element would be closer to a whole number if there were few to no electrons. This means having little to no electrons in the element's isotopes.
How would you set the Bunsen burner flame for normal heating?
by turning the Bunsen burner on and then turn the air whole until its open!
What elements are used in an electric heater filament?
The heating element in electric heaters and irons is made from an alloy of nickel and chronium called nichrome. It is usually made in the form of wire. The wire is often wound around a flat sheet of mica for support. Mica is a thin layered mineral that can withstand high temperatures.
Why Side mirror not heating in VW passat?
Is it just one mirror? I would look at a possible broken wire or heating element on the mirror. If it is both, I would look at a possible bad switch since it affects both mirrors.
What are the four features required to construct a working simple circuit?
power source, wire, switch, end fixture. Simplest circuit would be a power source and a heating element. No wire or switch needed.
What element is in the heating element for toasters?
That would most likely be a nickel and chrome alloy. Light bulbs use tungsten.
What would cause a 1996 Mitsubishi Galant to have no heat?
heating element stopped working
Why does a hairdryer on the 240 volt setting work in the US and does this mean the switch to change the voltage is faulty and it's not really operating on 240 volts?
Hair dryers usually have a HIGH and a LOW setting. The HIGH heating element is about 8 ohms. The LOW heating element is about 32 ohms. voltage (squared) / resistance = power (watts) 120*120 / 8 = 1800 watts ( HIGH ) 120*120 / 32 = 450 watts ( LOW ) When the voltage switch is set to 240 volts, ALL it does is limit the HIGH/LOW switch to the LOW setting. 240*240 / 32 = 1800 watts ( LOW ) 240*240 / 8 = 7200 watts ( HIGH ) (the heating element would burn out)
What will happen if the heating element is near at the top of the kettle?
In that case, it would be less efficient. Hot water rises to the top, mixing the water (if the heating element is at the bottom). When it is at the top, the water won't mix as well, and more heat would be wasted.
What causes a hot water heater to stop heating the water?
There are a number of causes as to why a hot water heater would stop heating the water. It could be due to a fault in the circuit breaker or a problem with the element, limit switch or thermostat. Unless you know what you are doing, you should contact a qualified plumber or electrician to rectify the issue.
Why would your heating system only come on sometimes in a 1999 Olds Intrigue?
Possibly related to an ignition switch problem.
Is whole grain wheat a element?
No, why would it be anyways. it is part of the food group.
What would cause the average atomic mass to be close to a whole number?
The average atomic mass of an element would be closer to a whole number if there were few to no electrons. This means having little to no electrons in the element's isotopes.
How do you replace the bulb in the seat heater switch console of a 2001 Subaru Outback Limited Wagon?
The light in the switch can not be changed, the whole switch would need to be replaced.
What is a single reaction a dublle replacement reaction?
You can identify a single replacement reaction because the reactants are a compound + an element. The products of a single replacement reaction are found by switching the element with another element in the compound. Metals switch with metals, non-metals switch with non-metals, and the most reactive element is always in the compound. A double replacement reaction can be identified because the reactants are always compound +compound. The products would also be two compounds but the elements would switch.
