0
What ia Standard of dc loop resistance of copper cable 0.5 mm dia?
Wiki User
∙ 10y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is redundant fiber optic cable?
fiber loop application
What kind of Pipe for closed loop heat pump?
heavy gauge copper
What is varley loop test?
A varley loop test is a test used to find the earth fault location in an underground cable. It uses the Wheatstone bridge to help determine the distance from the test point to a fault in a telephone or telegraph line or cable.
A cell of emf 3.0 volts and internal resistance of 0.01 ohm is connected through an ammeter of 0.05-ohm internal resistance to a 5.0 rheostat by wire having a total resistance of 0.85-ohm?
total voltage = 4.5V, total resistance = 3.5 ohms, loop current = 4.5V / 3.5 ohms = 1.286Atotal voltage = 9V, total resistance = 4 ohms, loop current = 9V / 4 ohms = 2.25Atotal voltage = 13.5V, total resistance = 4.5 ohms, loop current = 13.5V / 4.5 ohms = 3Aetc.There is no solution to your problem conditions.
How do you ground home recording system?
If you are getting a humming noise then you probably have an earth loop. This is where the resistance from one piece of equipment has a higher resistance than on other piece that it is connected to. The current flows through the lower resistance piece of equipment back to the earth on the mains causing the hum. There are two ways to cure this. the method used by recording studios is to create a star Earth. This is where all the earths from all devices comes back to a central earth point then to the mains earth. The alternative method is to break the shield at one end on the patch lead that goes from each device to interrupt the mains loop and force the earth current to run back down the mains cable earth.
What ia Standard of dc loop resistance of copper cable?
It depends on the length of th cable and the diameter of the copper cable used.
What is loop resistance?
It depends somewhat on context. A dc circuit consists of of a flow of current to the load and back to the source. This is often called the loop. The loop resistance would be the total resistance measured in ohms. In most power circuits the above would hold true in an ac circuit as well.
What is a drop loop?
do you mean drip loop? its where a cable coming down a wall, loops down then up before going through the wall. means water running down the cable will not enter wall with cable
Open loop and close loop system in injection moluld machine?
loop checking is perform before cable termination..the difference between a close loop and open loop is,tha close loop has a feedback while the open loop has not.
What is redundant fiber optic cable?
fiber loop application
How neutral brings the power to the source?
By creating a loop of equal resistance
What is an extra loop of DNA that contains antibiotic resistance what gene?
Plasmid
Where can one find some velcro cable ties?
You can find some velcro cable ties from the following sources: Amazon, MPD Hook and Loop, Newegg, The Gear Page, Amazon, eBay, Hook and Loop Direct, Fasten Nation, Cable Organiser.
What kind of Pipe for closed loop heat pump?
heavy gauge copper
The cord of an electric oven does not glow while the heating element glows.Why?
The cord is manufactured to have as low a resistance as possible, while the heating element is intentionally manufactured with a carefully controlled resistance. The current through the whole loop ... cord plus heater ... is determined by the resistance of the whole loop. The magnitude of the current 'I' is (E/R) ... E = the utility line voltage, R = resistance of the cord+heater. But the power dissipated by each individual resistance in the loop is proportional to the resistance of that section. P = I2R. So the heating element dissipates more power than the low-resistance line-cord does.
What is the tensile strength of copper wire?
to calulate the tensile strength of a copper wire is that get mass/weights, a clamp stand, a g clamp, a copper wire and a boss head. Tie a loop from a wire and hang it on the edge of the clamp stand, put the g clamp on the clamp stando it dosent fall of, anyway after you tie a loop at each ends of the copper wire hook the edge of the weights at the bottom of the loop keep putting on weights until it snaps and make sure you have googles on.
How do you release the latch pin on a convertible top manually when the cable attached to the release handle has snaped?
right behind the seatbelt mounts on both sides,there is a small cable with a loop on the end.stick you finger in the loop and pull,this will release the latch pin.
