There could be a series of problems. First, are all the wires hooked up? Is the bulb burned out? Is it just the switch that is not working? You should go and put in a new bulb, and see if it was just burned out.
wiring diagram of one bulb in two switches.. example, if switch a- on then switch b- off the bulb is on, switch a- off then switch b- on the bulb is on, switch a- on then switch b- on the bulb is off, switch a- off then switch b- off the bulb is off..
It is dependant on whether the switches are in wired in a parallel or series configuration. If the switches are wires in parallel then both switches would have to be off to turn the light bulb off. Either switch could turn the light bulb on. If the switches are wired in series then both switches would have to be on to turn the light bulb on. Either switch could turn the light bulb off.
It opens and closes a circuit and it makes the bulb turn off and on and it completes a circuit when it is closed.
When you turn It off it breaks the circuit. When it is turned on it closes the circuit. To have a light bulb turn on it need to have continuity. Hope that helps
It depend on where the switch is located in the circuit.
wiring diagram of one bulb in two switches.. example, if switch a- on then switch b- off the bulb is on, switch a- off then switch b- on the bulb is on, switch a- on then switch b- on the bulb is off, switch a- off then switch b- off the bulb is off..
It is a safety concern. With the switch before the bulb, the bulb is completely isolated from the potential source when the switch is turned off. With the switch behind the bulb, even if the switch is turned off, the potential source is still at the bulb. If any of these lamp holder parts touch the ground when removing the bulb the circuit will short out and trip the breaker. If you are grounded and touch any of the lamp holder parts you will get a nasty shock.
Say it is a power circuit, a light bulb is bright from the battery, flowing through the wires and the light bulb. There is a switch controling the power that goes through, so if you switched the off switch off, the power will no longer be flowing through(the light bulb wouldn't be bright any longer). Say it is a power circuit, a light bulb is bright from the battery, flowing through the wires and the light bulb. There is a switch controling the power that goes through, so if you switched the off switch off, the power will no longer be flowing through(the light bulb wouldn't be bright any longer).
switch lights off
because you are switch the hot leg, so it can be turn on an off.
The simplist answers is that electricity needs to complete a circuit fully. It stops flowing because there is no complete circuit. The switch is a device for opening and closing the circuit. When the switch is in the off position the circuit is said to be open and electricity cannot flow.
The bulb "pulses" because the circuit is not completely off. If the CF bulb is pulsing or flashing, it means that there is some kind of feedback loop providing at least some voltage to the bulb. Often lighted switches use the filament resistance to provide voltage to the internal bulb. Get rid of the lighted switch.
Perhaps by unscrewing the bulb light.
It is dependant on whether the switches are in wired in a parallel or series configuration. If the switches are wires in parallel then both switches would have to be off to turn the light bulb off. Either switch could turn the light bulb on. If the switches are wired in series then both switches would have to be on to turn the light bulb on. Either switch could turn the light bulb off.
switching on the tourch for example is when as you switch it on it will move the switch connecting it to a circuit that lights up the bulb and when you switch the switch off the switch will move breaking the circuit
turn 2 switches on wait one minute, turn one off go in the room if the bulb is off and warm it was the last one you turned off if its cold its the one you didnt touch and if its on its the only switch left on.
The OFF position on the light switch interrupts the flow of electricity to the light bulb. If the switch is ON, there is always electricity at the light socket, even when the light bulb is removed. if the lamp is still pluged in electricity is still flowing through the lamp even if it is off or on