0
What else can I help you with?
What is a hydrodynamic coupling?
A hydrodynamic coupling is used on a tractor to convert the power of the engine for other purposes. It allows you to operate equipment such as a post hole digger, hay baler, or log splitter from a connection on the tractor.
What Horse power is required for 575 New holland baler?
75 hp
How do you replace the twine on welger ap 45hay baler?
To replace the twine on a Welger AP 45 hay baler, first, ensure the baler is turned off and disconnect the power source for safety. Open the twine box and remove any remaining twine from the spools. Load the new twine onto the spools, threading it through the designated guides and tensioners as outlined in the user manual. Finally, secure the twine in place and test the baler to ensure proper operation.
Who is General Power Equipment?
A company in Ohio that distributes outdoor power equipment.
What are the main parts of combine harvester?
The header (reaper), the thresher, the separator, the storage bin, and, of course, the power unit, drive system, and operator station.
How much horsepower is required to run a 336 baler?
A 336 baler typically requires around 30 to 50 horsepower to operate effectively, depending on factors like the type of material being baled and the specific conditions of use. It's essential to ensure that the tractor or power source providing the horsepower is compatible with the baler's requirements for optimal performance. Always consult the manufacturer's specifications for precise horsepower recommendations.
How is a round hay bale made?
With a round hay baler. The baler is powered by the tractor through the PTO, an electrical control box, and hydraulics, which enables the operator full control over the baler. The tractor moves along the swath of hay, and the revolving pick-up cylinder picks up the swath and moves it into the baler chamber. In the baler chamber, the chains or belts move like a constant pulley system (there is more than one: bottom, top, and the two sides) rolling the hay, as it enters the chamber, into a cylinder. The cylindrical hay bale grows until it cannot expand anymore inside the baler. The size limit sensors in the baler go through to the control box in the tractor, often through audio alert, and the operator either keeps going until he can judge when the bale is big enough and/or until he sees it is nice and tightly packed enough inside the baler to let stop and let it out. But, before he lets it out, he has to stop first and, with the control box, apply the strings or netting to the bale. There is no need to worry about tying, as the baler machine does it automatically. Once the bale has been entwined (literally), the tractor and baler powers down, stopping the movement of the belts and pick-up wheel in/on the baler, then the operator lifts the back end of the baler (with the control box in the tractor of course, not manually), and initiates the belts or chains to eject the bale out of the baler. The back door closes, the baler power ups again, and resumes creating another bale. This process repeats until the operator has to quit because of one of four things: 1) the baler gets plugged up (most commonly in the pick-up shaft) 2) it starts to rain 3) it gets too late in the evening and the hay starts to, what we call, "toughen up." 4) he finished baling up the hay field
What is a power plant footprint?
A power plant footprint refers to the physical space occupied by a power plant, including the buildings, equipment, and land that make up the facility. It is a measure of the spatial impact and land use associated with a power plant's operations. The footprint can vary depending on the type and capacity of the power plant.
How do you get the plunger out of a New Holland baler?
To remove the plunger from a New Holland baler, first ensure the machine is turned off and disconnected from any power source. Next, access the plunger area by opening the appropriate access panels. Loosen and remove any bolts or fasteners securing the plunger, then carefully slide it out, ensuring to follow any specific instructions in the baler's manual for your model to avoid damage. Always consult the operator's manual for detailed procedures and safety precautions.
The minimum distance between the declination station and such objects as power lines and electrical equipment is?
Power lines and electronic equipment: 150m
What is the NAICS Code for Mechanical Power Transmission Equipment Manufacturing?
NAICS 333613 applies to Mechanical Power Transmission Equipment Manufacturing.
What is the symbol for Global Power Equipment Group Inc in the NYSE?
The symbol for Global Power Equipment Group Inc in the NYSE is: GLPW.
