0
What else can I help you with?
What is the effect on tool life surface finish and dimensional accuracy when applying roughing and finishing cuts?
Tool life is greatly shortened when used for both roughing and finishing thus affecting dimensional accuracy and surface finish badly as tool begin to wear off or get chipped, whereas, tool life gets longer when different tools are being used for roughing and finishing again dimensional accuracy and surface finish is affected but this time by achieving good results.
Furminator DeShedding Tool for Dogs and Cats How is it for Grooming Pets?
The Furminator DeShedding Tool for Dogs and Cats is good for the de-shedding aspect of grooming, but not really for finishing.
What puts the head of nails below the surface?
A nail set is the tool used to drive finishing nails below the surface.
Where is grinding most commonly used?
Grinding is most commonly used in floor finishing, to produce fine edge of cutting tool.
What is a reamer tool used for?
A reamer is a cutting tool used for finishing work on holes that have been made with a drill or borer. The reamer can finish of the hole to the exact diameter required and also smooth the edge.
What is honing process?
Honing is a sort of hole finishing operation performed after drilling. The honing tool is a multipoint cutting tool. There will thin projections parallel to the length of tool extending from one cross section to other. When the tool is inserted into the hole, a loading is given on the cross section of the tool which extends a spring attached to the projections pushing the "abrasive cutting edge" out side and then it is rotated so as to give finishing. This method is generally use in the cylinder of IC engines.. Rough sketch:- ------------------------------ ================= ================= ----------------------------- Dotted arrows show the 2 peripheries of the cutting tool and "equal to sign" shows edges of abrasives. The pushing of spring radially connected to the centre pushes the cutting edge of abrasives out which enables finishing operation
What are the tool holding device in cnc lathe?
In a CNC lathe, the tool holding devices are crucial for securely fastening the cutting tools during machining operations. Common types include toolholders such as collet chucks, tool posts, and quick-change tool holders. These devices ensure precise alignment and stability of the tools, allowing for accurate cutting and finishing of the workpiece. Proper selection and maintenance of tool holders are essential for optimal performance and tool longevity.
What did Caesar's own adopted son do to tarnish Caesar's memory?
Nothing. Augustus was Caesar's adopted son and he honored the memory of Caesar by finishing the temple to him and finishing his forum.Nothing. Augustus was Caesar's adopted son and he honored the memory of Caesar by finishing the temple to him and finishing his forum.Nothing. Augustus was Caesar's adopted son and he honored the memory of Caesar by finishing the temple to him and finishing his forum.Nothing. Augustus was Caesar's adopted son and he honored the memory of Caesar by finishing the temple to him and finishing his forum.Nothing. Augustus was Caesar's adopted son and he honored the memory of Caesar by finishing the temple to him and finishing his forum.Nothing. Augustus was Caesar's adopted son and he honored the memory of Caesar by finishing the temple to him and finishing his forum.Nothing. Augustus was Caesar's adopted son and he honored the memory of Caesar by finishing the temple to him and finishing his forum.Nothing. Augustus was Caesar's adopted son and he honored the memory of Caesar by finishing the temple to him and finishing his forum.Nothing. Augustus was Caesar's adopted son and he honored the memory of Caesar by finishing the temple to him and finishing his forum.
What is the design procedure for single point cutting tool?
1.you have to know the workpiece material 2.tool material 3.type of machining process 4.sinle point or multi point tool 5.roughing or finishing cut 6.stresses that applied on the tool 7.dry or wet machining 8.cutting conditions,speed,feed and depth of cut 9.productivity and tool life 10.surface finish required
What is use of grinding?
Grinding is commonly associated with lathe tool making with an abrasive wheel that turns on average 2800-3000 rpm, surface finishing and creating flats through methods such as lapping.
When was Finishing the Game created?
Finishing the Game was created in 2007.
When was The Finishing Stroke created?
The Finishing Stroke was created in 1958.
