A trap instruction is a software interrupt. It's generated by an error or by a user program when it needs the operating system to perform an operation (a system call).
Answer: An interrupt is a hardware-generated change-of-flow within the system. An interrupt handler is summoned to deal with the cause of the interrupt; control is then returned to the interrupted context and instruction. A trap is a software-generated interrupt. An interrupt can be used to signal the completion of an I/O to obviate the need for device polling. A trap can be used to call operating system routines or to catch arithmetic errors.Type your answer here...
the trap
The Mouse Trap
You know when they do disappearing acts on a stage? Like when a magician makes a person "disappear?" Well they actually made that person fall through the trap door. The trap door is usually situated around center stage and is used to move props or even people. It creates somewhat of an illusion.
That depends on what period you are referring to. In Shakespeare's day they rose from a trap door in the floor of the stage. Much later, a devise called a Corsican Trap, from the play The Corsican Brothers combined a trap door with a huge treadmill that allowed the ghost to rise vertically and float horizontally at the same time.
A system call is started with some form of trap-instruction.
The TRAP instruction in the 8085 is NONMASKABLE, which means it cannot be masked, i.e. it cannot be disabled. The only way to mask or disable TRAP is with external hardware, such as an I/O pin and an AND gate.
Processor serves the interrupt request after completing the execution of the current instruction.
In the 8085, trap, intr, and rstx.5 lines are checked on the falling edge of clock, at the beginning of the last T cycle of an instruction, or approximately one clock cycle before ALE.
Trap is actually a software generated interrupt caused either by an error (for example division by zero, invalid memory access etc.), or by an specific request by an operating system service generated by a user program. Trap is sometimes called Exception. The hardware or software can generate these interrupts. When the interrupt or trap occurs, the hardware therefore, transfer control to the operating system which first preserves the current state of the system by saving the current CPU registers contents and program counter's value. after this, the focus shifts to the determination of which type of interrupt has occured. For each type of interrupt, separate segmants of code in the operating system determine what action should be taken and thus the system keeps on functioning by executing coputational instruction, I/O instruction, torage instruction etc.
Trap is actually a software generated interrupt caused either by an error (for example division by zero, invalid memory access etc.), or by an specific request by an operating system service generated by a user program. Trap is sometimes called Exception. The hardware or software can generate these interrupts. When the interrupt or trap occurs, the hardware therefore, transfer control to the operating system which first preserves the current state of the system by saving the current CPU registers contents and program counter's value. after this, the focus shifts to the determination of which type of interrupt has occured. For each type of interrupt, separate segmants of code in the operating system determine what action should be taken and thus the system keeps on functioning by executing coputational instruction, I/O instruction, torage instruction etc.
The direction flag (DF) controls the direction of repeated string instructions. The trap flag (TF) executes one instruction and then executes a debug (INT 1) instruction so that a debugger can single step through a program.
Masking in the 8085 is when certain interrupts are disabled, or masked, by instruction execution. TRAP is not maskable. INTR, RST7.5, RST6.5, and RST5.5 are maskable as a group with the EI and DI instructions. RST7.5, RST6.5, and RST5.5 are selectively maskable, even after the EI instruction, by using the RIM and SIM instructions.
Which of the following is a legal and commonly used trap? bell trap S trap drum trap P trap
which of the following is a legal and commonly used trap? bell trap S trap drum trap or P trap
Steam trap? Grease trap? moisture trap (drip leg)? Running trap? "P" trap? Drum trap. 1/2 S trap? sediment trap?
P trap, Running trap, Grease trap , sediment trap,