0
Crown molding is used for different end results. If you are using it for baseboards you will use a stud sensor to locate the studs in the wall and than shoot the molding into the wall with a finish nail that is long enough to secure it through the sheetrock into the wooden stud. If the molding is used around doors you don't need a stud sensor. There are studs framing in the opening. Most door openings are framed in two inches bigger than the prehung door. This allows the installer the ability to slide in the door, shim it to level, and than shoot it in. That is why you should have no trouble shooting in molding around a door. If the molding is used in furniture there is a wooden cleat behind the molding that you can shoot into with a finish nail. You will than fill in the hole left with a finish nail with putty.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How To Install Crown Molding?
No one wants a dull room with plain walls and nothing decorative to accent that particular room. Why not add crown modeling to your existing walls so that it will give that spice you were looking for. It is fairly easy to install. And yes working over your head can be exhausting but the results are well worth it. Here is a step by step guide to help you along the way with installing crown molding.Step 1. Measurements come first. Measure around the top of the walls to get the linear footage required for the job. Add a little extra to your final measurement so you can account for any miscalculations.Step 2. Pick out the style of molding you want for that room. Make sure you buy the finish as well.Step 3. It is best to by your molding in lengths that require less splicing. But sometimes splicing can not be avoided when the room is big.Step 4. Stain or paint your molding and allow for adequate drying time.Step 5. Cut the needed angles for the corners. Using a miter saw is best to achieve the results you are looking for.Step 6. Set up your work area so that you have everything handy.Step 7. Take the first piece of molding and place it into the corner of the wall. Next you will need to cope cut the second piece that will be joining the angle in the corner. This is best achieved with the use of a miter saw.Step 8. Take your utility knife and trim the excess the saw left behind.Step 9. Now it is time to figure out the location of the joist. Drill holes to avoid the molding from splitting.Step 10. Secure the molding with just a few nails. Be sure to use nails according to the thickness of your molding. If you are satisfied with the position, finish nailing it up.Step 11. Use nail set to countersink the rest of the nails.Step 12. Now its time to fill in all nail holes with wood putty. Also use wood putty to cover any small gaps where the molding was joined.Step 13. Use the same finish as you did on the molding on the nail holes and areas you used wood putty.
How to paint using a Power painter on crown molding?
First, when painting crown molding, you will need to find an out of the way place for painting in. This place must fit the following criteria... * have sufficient square footage to accommodate all of the crown molding laid out flat and allow room for you to safely reach every inch of every stick. (painting crown molding is difficult if you can't reach it) * is totally dry. Do Not let your painted crown molding sit outside over night where it is vulnerable to dew or fog. * is safe from air born dust, dirt, leaves etc. Cover the entire floor space with painters plastic and lay out the crown molding in rows. For easy painting of your crown molding, it's best to group the rows in three to five sticks depending on your arm length. Also it is much easier to paint if they are raised up off the ground. I use buckets and 2x4s to do this. If you crown molding is white already then it is primered, you can skip that step. If not you will need to apply a coat of primer to seal the molding. No need to go very thick with it, one coat will do. Once dry, sand the primer coat lightly.Applying Paint:Generously apply the paint to two sticks at a time. Keep the spray nozzle consistently at the same distance from the crown molding (read the instructions on the box for the exact space)Repeat the process for all the sticks and apply a second coat once dry.
What is Dentil Molding?
Made from Marble, Wood, polyurethane, PVC, Resin, Gypsum - Moulding or Molding is a 2 piece crown. Crown Moulding with a straight crown and another small piece glued in wood and inserted in the rabit, mid way down on the face. All other materials are molded with the square blocks that make up the dentil as 1 item.
The best way to get nail glue of your skin?
There's no exact way to get it off :P usually try nail polish remover, or exfoliating the skin/nail glue.
Installing Crown Molding?
Start by cutting a small piece of the crown molding preferably about 1 foot. Start by placing the crown molding in the proper position on the ceiling and the wall. Make a small pencil line on On the wall on the bottom of the crown molding Measured the distance from the ceiling to the pencil line And cut a piece of crown molding the same size. Go around the room and mark off the line preferably about 2 to 3 feet apart from each other. Next you need to find the angles of the corners You can do that with a protractor tool that you can purchase at the Home Depot for about $5-$10 Next you need to get your measurements. This will usually require a helper To hold the other end of the tape measure. Measure from wall to wall using the tape measure a simple trick is to make a small pencil line in the centers of the corners to make sure you are measuring at the proper location. It usually helps to write the number on the wall but make sure you put it above the line so you do not need to paint it back Next you need to find your Studs which are commonly known as 2 x 4. With a stud finder you will be able to find the studs easier you can usually purchase one of them at home Home Depot for about $20
What is the best way to remove nail polish from skin?
The best way to remove nail polish from skin is to put nail polish remover on a cotton ball and put it on the part of your skin and rub it after you get it off make sure you wash the area you put nail polish remover on
What is the best way to seal a partial tube of caulking?
long nail
What is the best way to get nail polish out of pants?
Try soaking it in warm water then using Nail Polish remover and throwing them in the wash.
How do i install crown molding?
Crown molding can be one of the most difficult do-it-yourself tasks for a homeowner because it requires more complex math and machinery skills. The TV show "This Old House" has come up with a way to help simplify the mathematics aspect of the process. You can see the step-by-step process here: http://www.thisoldhouse.com/toh/how-to/intro/0,,1016651,00.html You will need a miter saw and simple hand tools to install crown molding. The vital thing is to make the cuts at correct angles so that your corners fit correctly. You can go to http://www.thisoldhouse.com/toh/how-to/intro/0,,1016651,00.html for a thorough walkthrough.
How do you get rid of caluses?
The best way to get rid of a calus is to file it off with a nail file.
How fast a nail will rust by water?
This really depends on the concentration of impurities in water. More the impurities, faster it will rust the iron nail. To reduce rusting of any iron the best way is to paint the nail.
How do you make silver nail polish?
The best way is to get gray nal polish and white nail polish. then add fine silver glitter and let it sit.
