What is diagnostic code 55 on a 1997 Jeep Cherokee?
it means end of diagnostic check
Diagnostic code 43 in the 1997 Jeep Grand Cherokee refers to an issue with the distributor. This often causes the Jeep to stall at operating temperature.
this code is a gross leak in the evaporative emissions system....most likely a loose or bad gas cap.
bad connection to O2 sensor, or dirty/bad O2 sensor.... clean or replace with new
Simple: Plug a code reader into the diagnostic port (under steering wheel). A good auto parts store like O'Reilly or AutoZone can usually do this for free.
catalytic converter circuit
O2 sensor or wiring
EGR Valve Sensor....
Map sensor voltage low.
Error code 66 on a 1997 Jeep Cherokee means TCM to PCM failure. This code means that the transmission control model is not communicating with the powertrain control model.
55 is end of message. If that is the only code you have, then there isn't a problem
That code is a manufactureres code. You can type jeep diagnostic code p1494 into bing or google and get it to come up for you.
The diagnostic code 12 51 55 is actually not a code for the 1994 Jeep Grand Cherokee Laredo. The 12 means that it has started searching for codes. The 51 is oxygen sensor stuck lean. The 55 means it is finished searching for codes. Getting this means nothing is wrong.
Trouble code P1782 means: Pressure switch circuit: 2-4
P0783: 3-4 shift malfunction
Codes on a 1995 Jeep are two digits long. So 5 means nothing.
Trouble code P0351 means: Ignition Coil 1 Primary Circuit Malfunction
6???? the code should be like this ie: P0301. Please reask question with the code number..
Code 12 just means that the battery has been recently disconnected
Diagnostic Code 12 on a 1995 Grand Cherokee just means that your battery has been dead or disconnected within the last 50 ignition cycles.
Trouble code P1694 means: No CCD message from PCM- Aisin transmission
P1491 = radiator fan relay circuit
Po122 means the tps/pedal position sensor A has a low circuit output. P1763 is not in my code book. It is a manufactures code and probably means the same thing. You can look it up by typing diagnostic code p1763 in the search line on your computer. Good luck..
This question does not make any sense. Please ask a new question with better info.
usually codes P030# mean misfiring cylinders the last number would be the # of the cylinder.
P0123 TPS volts high. Replace the throttle position sensor.
possible faulty leak detection pump
It means the battery has been disconnected from the pcm with in the last 50 key on cycles
the code po455 is a evaporative emmissions code that tells you your fuel tank has a gross fuel vapor leak which is usually caused by the gas cap being loose or a problem with it. one other cause is evap vent control valve may be sticking or not functioning properly.
Code 31, evaporative purge solenoid incorrect flow.There is likely a broken hose between the fuel tank and the engine.
Trouble code P1899 means: Park/ Neutral switch stuck in park or gear
where do I find the color code for a 1989 jeep Cherokee and what does it look like
Trouble code P0321 means:Ignition/distributor engine speed input circuit range/performance
Trouble code P1762 means: Governor pressure sensor offset improper voltage
With an OBD2 scan tool. or flip switch till odometer comes on repeat two times watch for code done means no codes
122 Throttle position sensor voltage low you need to clean the body throttle only. just applay carbritor cleaner to it and you go
Large vapor leak in the evaporative emissions system You could have a gasoline vapor leak anywhere from the gas cap to the tank to the engine.
51** Fuel System Lean A lean air/fuel mixture has been indicated by an abnormally rich correction factor
I don't know about a Grand Cherokee, but in a 2005 Jeep Wrangler you turn your ignition 3 times with out turning the motor over. Turn your key to start, then off, then start, then off, then start and leave in start position, a code will be displayed in the odometer area. Maybe its the same for a Grand Cherokee. If that doesn't work a scan tool is required.
Cylinder #4 misfire.
What does an ABS code 12 mean for a 1996 jeep grand chekoee?
Trouble code P0605 means: Internal TCM Error
12 indicates battery input to the Powertrain Control Module (PCM) was disconnected during the last 50 key starts. -Jkanly
Battery has been disconnected.
Trouble code P0734 means:Gear 4 incorrect ratio
Trouble code P0700 means:Transmission control system malfunction
Bad throttle position sensor
in a jeep grand Cherokee the code 11 no distributor reference signal detected during cranking. check the circuit between the distributor and pcm code 55 means the code reading is done.. that's all the codes the pcm has to relay to you.