0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why we never disconnect the tubing from the gas cock without first turning the gas off?
If the gas is not turned off first, on removing the tubing, gas will escape - very dangerous.
What arethe Uses of clay shield and rubber tubing?
The clay shield and rubber tubing are useful in heating during experiments. The rubber tubing connects the Bunsen burner to the gas outlet. The tubing enables the water to cool as it flows through the condenser during the distillation process.
What is gas lift?
Gas lift is a method used in increasing the production of oil from a well by injecting gas after the inherent pressure in the well must have dropped after a fairly long time(this is a function of the well dynamics ). Gas gotten from the well along with the oil is removed through separators and compressed before re-injection into the tubing casing annulus. The gas enters into the tubing through gas mandrels on the tubing strings and through a gas valve. The gas aerates the fluid and makes it less dense thereby reducing its viscosity and this makes the formation pressure push out more fluid.
What are the 7 parts of the tirrill burner?
A tirrill burner has a barrel, air vents, gas inlet and needle valve. The barrel turns on a threaded mount to allow air; the air vents limit the air entry into the barrel; the gas inlet is where the gas flows; and the needle valve regulates the gas flow.
How do you combine the Bunsen burner to the LP gas cylinder?
There will be a valve at the bottom of the Bunsen burner. Using a rubber tubing connect the valve to the regulator of the LPG cylinder.
What is the phone number of dr brenda marsh tucson Arizona?
It is yeah ehd It is yeah ehd It is yeah ehd
Why we never disconnect the tubing from the gas cock without first turning the gas off?
If the gas is not turned off first, on removing the tubing, gas will escape - very dangerous.
What is the function of regulator in the rubber tubing?
A regulator in rubber tubing is put there to regulate the flow of liquid or gas through the tubing. With a regulator, the flow can be slowed or even stopped if necessary.
What is closed in tubing head pressure in Oil and Gas industry?
usually, the tubing head is the cross-tee connected by flange both at top and bottom. The tubing head is installed on the flange of the casing head, so as to hang the tubing string and seal the annular space between the tubing string and the production casing. The tubing head is made up of the tubing head cross-tee and the tubing hanger.
How do you get the gas out of a 1994 Cutlass Supreme gas tank?
Get a bucket and a length of tubing. Stick the tubing into the tank. Start sucking to create a suction. Once you taste gasoline, stick the other end into the bucket. Voila, the gas will start pouring out !
How do you use a Bunsen burner?
Put the rubber tubing onto the gas tap Then turn on the gas tap
Is it possible to download saved programs from a DVR dish network to a camcorder?
Our DVRs use a certain programming language. You can transfer recorded events from the receiver to an EHD (certain requirements for the EHD) but you wouldn't be able to transfer to a camcorder.
Why is the nozzle hole is very much smaller than gas inlet?
This is to increase the velocity of the gas as it enters the rubber tubing. The higher velocity means it will travel farther in tubing while still remaining at low pressures.
What arethe Uses of clay shield and rubber tubing?
The clay shield and rubber tubing are useful in heating during experiments. The rubber tubing connects the Bunsen burner to the gas outlet. The tubing enables the water to cool as it flows through the condenser during the distillation process.
What is gas lift?
Gas lift is a method used in increasing the production of oil from a well by injecting gas after the inherent pressure in the well must have dropped after a fairly long time(this is a function of the well dynamics ). Gas gotten from the well along with the oil is removed through separators and compressed before re-injection into the tubing casing annulus. The gas enters into the tubing through gas mandrels on the tubing strings and through a gas valve. The gas aerates the fluid and makes it less dense thereby reducing its viscosity and this makes the formation pressure push out more fluid.
Why do gas bubbles push water out of their way as they emerge from the end of an aquarium tube?
They have their own mass and volume, and they are coming out of the tubing with more force than the water surrounding the tubing.
In the figure GHF equal EHD. which statement is true by CPCTC?
Angle HDE = angle HFG.
