When circuit boards are assembled, the parts are soldered on. In order for the solder to make a good connection to the parts and to the board, a substance called flux is mixed into the solder. It removes oxidation and cleans up the surfaces of the different parts so that the solder can stick to them. After the board is assembled, there is still flux on the board.
Flux remover dissolves the flux and washes it away.
when a current flow through the coil then flux produced around the coil . if the flux linked same produced coil only then the flux is said to be leakage flux. flux produced by one coil ,but linked with another coil then the flu is said to be mutual flux.
dc flux is caused by dc current (flux and current are proportional), it is a constant value. Put an inductor (or transformer winding) across a battery and you will get dc flux. ac flux is caused by ac current (flux and current are proportional), it is a moving value, the flux moves with the current, typically cyclical but the waveform is arbitrary as long as we're moving.
Flux incresed with the increase of scalar quantity
when a load is connected to a transformer current(say I2) flows through secondary coil thus an M.M.F (N2I2) is produced ,this produces the secondary flux. This flux reduces the the main flux induced in the primary & also reduces E.M.F E1 in the primary As a result more current is drawn from the supply. This additional current drawn is due to the load component(say I2' ) This I2' is anti-phase with I2.This I2' sets a flux which opposes the secondary flux & helps the main flux. The load component flux neutralises the secondary flux produced by I2 .The M.M.F N1I2' balances N2I2.Thus the net flux is always at constant level. As practically flux is constant,the core loss is constant for all loads. Hence a transformer is always called a Constant Flux Machine.
Yes it can. I use flux core wire because there is no need for gas with flux wire.
i) leakage flux is those flux which goes through the air and linkage flux is those flux whose go through the cell. ii)leakage flux is the loss at flux but linkage flu is warning flux. iii)leakage flux is cause of eddy current loss and linkage flux is case of copper loss.
The Ratio of the total flux ( flux in iron path) to the useful flux (flux in air gap)
when a current flow through the coil then flux produced around the coil . if the flux linked same produced coil only then the flux is said to be leakage flux. flux produced by one coil ,but linked with another coil then the flu is said to be mutual flux.
when a current flow through the coil then flux produced around the coil . if the flux linked same produced coil only then the flux is said to be leakage flux. flux produced by one coil ,but linked with another coil then the flu is said to be mutual flux.
In a Transformer, Core flux is the difference of primary flux and Secondary flux which are opposite to each other in direction. There difference is equal to the no load flux at all loads. So, some of primary flux passes through the core and remaining becomes leakage flux (Because Secondary flux forces it to get out of the core). Same is the case with Secondary flux. Now, flux is directly proportional to Voltage and Current. When Current increases due to increased load (and voltage remains same): Then both primary and secondary flux increase. Because both of them increase, so there difference remains same. And all remaining flux is forced out. Hence leakage flux increases with current, but Core flux remains constant. When Primary Voltage is increased: Then only primary flux increases. So difference of this new increased primary flux and previous same secondary flux increases. Hence Core flux increases with voltage, But leakage flux does not. That's how In transformer core flux depends on voltage whereas leakage flux depends on current.
Flux gusto
light speeeed mofos
critical heat flux is the heat flux at critical point
Types of flux - Electric and Magnetic Flux. Electric field flux through a closed surface is equal to the change enclosed in the surface, or the rate of change of magnetic flux is equal to the induced voltage around the surface.
dc flux is caused by dc current (flux and current are proportional), it is a constant value. Put an inductor (or transformer winding) across a battery and you will get dc flux. ac flux is caused by ac current (flux and current are proportional), it is a moving value, the flux moves with the current, typically cyclical but the waveform is arbitrary as long as we're moving.
Basically useful fluke is the flux that flows with in the magnetic circuit of an armature. That is why when there is an air gap the flux enters the armature which makes it useful flux! Hope that answers your question!
once flux density is known multiply to it the area perpendicular to the flux lines . the product is the total flux passing through the area. If field strength is known , get the flux density by pultiplying to it the permeability of the medium. then flux can be obtained as above. from : govind Kunkolienker kunkolienker@yahoo.com