0
What else can I help you with?
How do you determine the work done in a ferromagnet in going round a hysteresis loop?
When a hysteresis loop is plotted on a graph ( X: Current, Y: Magnetic Field Strength ) for the core of any substance, the area covered by the loop (on both sides of the x-axis) will give the total energy involved or work done in one cycle of magnetisation and demagnetisation.
What is magnetic hysteresis?
Magnetic hysteresis is the phenomenon where the magnetization of a material depends not only on the current magnetic field, but also its history. When the magnetic field is applied and then removed, the material retains some magnetization, showing a lag or "memory" in its response to changing magnetic fields. This results in the characteristic hysteresis loop observed in magnetic materials.
A contour line that forms a closed loop and has small dashes pointing to the inside of the loop represents what?
Hysteresis loops tell about the magnetic properties of a material. E.g. wider loops indicate that the material is magnetically hard (i.e. it retains magnetisation even if the applied field is removed, permanent magnetics have much wider hysteresis loops)whereas thinner loops represent it to be soft (if the magnetic field is removed, the material doens't show any magentism). This is one advantage of hysteresis loops. further, such loops can identify the grain size of a material and much more. hope it answers your question.
Why Soft Iron is suitable for preparing electromagnets?
soft iron B-H curve area is very high and hysteresis loss is proportional to it frequency or no of loop cycles per sec and area of loop so hysteresis loss increases in soft iron as electro magnet
Calibration of gas chromatography?
What is the precedure for calibration of gas chromatography? How calibration is perform for gas chromatography? What is the precedure for calibration of gas chromatography? How calibration is perform for gas chromatography?
What is hysteresis loop in stress and strain?
the leading or lagging between the stress and strain is called hysteresis loop
How can you measure the hysteresis loop of the ferroelectric materials and what is the name of the instruments used for the measurements of the hysteresis loop?
The hysteresis loop of ferroelectric materials can be measured using a ferroelectric tester or a precision impedance analyzer. These instruments apply a voltage sweep to the material and measure the resulting polarization response, capturing the hysteresis loop which shows the relationship between polarization and applied electric field.
The area of hysteresis loop in a ferromagnetic material of?
The area of the hysteresis loop in a ferromagnetic material represents the energy losses that occur during the magnetization and demagnetization processes. It is a measure of the energy dissipated as heat due to the magnetic domain reorientation within the material. The larger the area of the hysteresis loop, the greater the energy losses and the lower the efficiency of the material in applications such as transformers or inductors.
Formula of Hysteresis loss and Eddy current loss?
hysteresis loss = N1/N2 R2/R1 C1/A1 (area of the loop)(vertical sensitivity) (horizontal sensitiivity
How do you determine the work done in a ferromagnet in going round a hysteresis loop?
When a hysteresis loop is plotted on a graph ( X: Current, Y: Magnetic Field Strength ) for the core of any substance, the area covered by the loop (on both sides of the x-axis) will give the total energy involved or work done in one cycle of magnetisation and demagnetisation.
How do you select core in Transformer Design?
The material used in the manufacture of transformer cores must have a hysteresis loop with a very small area, as it is the area of the hysteresis loop that determines the hysteresis losses of the core material. The core material should also be resistive, in order to reduce eddy current losses (which is further improved by laminating the core). Many transformer manufacturers use their own variations on what is basically a silicon-steel.A hysteresis curve, or loop, is a graph of flux density plotted against magnetising force, and basically describes the ease (or difficulty) with which the core material can be magnetised and demagnetised as the magnetising current changes magnitude and direction.
What is the significance of looping?
In hysteresis materials it represents the energy dissipated in them during the cycle of magnetization & demagnetization (just refer any hysteresis loop diagram) . This is used in many applications especially in aerospace to damp the oscillations in satellite.
What is magnetic hysteresis?
Magnetic hysteresis is the phenomenon where the magnetization of a material depends not only on the current magnetic field, but also its history. When the magnetic field is applied and then removed, the material retains some magnetization, showing a lag or "memory" in its response to changing magnetic fields. This results in the characteristic hysteresis loop observed in magnetic materials.
Why area of hysteresis loop is change with temperature?
Disorder. Each unit cell has its own dipole moment, which, when there is a net polarisation, are described as ordered. At high T, the direction of the dipole moments randomises, giving a disordered material with no net polarisation.Phase transitions that can open up new possibilities for dipole moments to form. In this case, there is a jump at 0°C, and at 90°C, where the loop becomes taller.
What do you mean by hysteresis?
A hysteresis loop is when the threshold to make a change in a system is different than the threshold to undo the change. Typically, in an op amp used as a switch, this is done with a small positive feedback, reducing the chance of oscillation when the input is near one of the two thresholds.
Why when you calibrate your Nintendo ds lite does it still touch the wrong part?
When I calibrate mine, I am stuck in an endless loop of calibration.
How do you reduce the hysteresis loss?
Hysteresis losses are a function of the magnetic characteristics of the magnetic circuit, so there is very little you can do to minimise hysteresis losses other than to reduce the primary voltage to a transformer if that is at all practicable. These losses are really in the hands of the manufacturers who design and manufacture magnetic circuits.
